escutcheon coin turn

RELATED FAQS

Question
Answer
This change was implemented in firmware package CO.A.6 (or later) to help the customer in the communication and coupling process between the CO200 (CO250) and the hand held device (HHD). ...
The green LED is to be lit up until the spindle (Triangles and Key Switch) are aligned properly; providing a visual indication of the problem.  
If the mechanical alignment of the triangles on the back of the outside escutcheon are not aligned, the CO200 or CO250 will not connect with the SUS/HHD and will appear to be unresponsive...
In firmware CO.A.6 (or later) the Schlage button on the CO200 (CO250) will turn green anytime that the spindle triangles on the front escutcheon are out of alignment or the mechanical key switch is...
When unlocking the CO200 door by mechanical key override, the green led will be continuously ON until the key is released. This will occur after firmware CO.A.6 (or later) has been installed int...
Both adaptors are used on the B250 Series for doors prepped with a 2-1/8" bored hole instead of the 1-1/2" bored hole. 38-031 is a light gauge ring for use under a cylinder, diameter is 2 1/2" ...
  Schlage H-Series Escutcheons    Part Number  Description Dimension   07-057  Inside escutcheon and turn  6.92" x 2.75"  07-035  Inside escutcheon, dummy - H170  6.92" x 2...
Outside Knob/Lever and Rose/Escutcheon Assemblies      Part Number  Description    A Rose with Knob/Lever  09-506  Designs: 01 02 03 05 06 07 12 17 18 OME 41 42     09-655  Des...
Coin cell replacement is not immediately registered by the AD200/250 firmware.
Performing a processor reset (pressing and releasing S1 on the Main PCB Assembly) will register the new coin cell.
Cycling lock power (i.e., disconnecting and reconnecting the "AA" battery pack) will register the new coin cell.
The coin cell part number is CR2025 - 3 volt lithium - available at most battery or electronics stores.
There is not a coin cell on the CO100.
The Schlage mortise cylinder coin turn is part number 09-900 XL12-196.  This cylinder coin turn in non-handed so it can rotate freely in both directions. Can be used with the L9496.  Coin turn wil...
Coin cell replacement is not immediately registered by the CT5000 firmware.
Performing a processor reset (pressing and releasing the RESET button) will register the new coin cell.
Coin Cell part number is CR2025 - 3Volt Lithium - available at most any battery store.
In late July, 2014, Schlage began taking orders for a new high visibility indicator for both N escutcheon and sectional trim applications.  A complete listing of lock functions and part number...
The L Series mortise indicator datasheet can be found here. Includes how to order.
The coin cell battery is not used by the WRI400.
The following list of cylinders were not affected by the change to modular cylinder:    09-900, 09-904, 09-905, 09-907 mortise cylinder turnsSmall format interchangeab...
The coin cell Nuisance Delay on CO200 and CO250 can be temporarily disabled using the Schlage Utility Software.
Once disabled via the SUS application, the CO lock will no longer delay the access for valid credentials.
If your CO lock began indicating a low coin cell (Nuisance Delay) after a door file has been downloaded, the coin cell is low and should be replaced. (CR2032)The coin cell Nuisance Delay will be "A...
The coin cell Nuisance Delay settings in the SUS application is not available until such time that a Door file is successfully downloaded to the lockset.
The coin cell is ignored when the lock sets are used with Manual Programming ONLY or while in Construction mode.
The 09-900 mortise cylinder thumbturn has three handing options: right hand, left hand, and non-handed.  Handing of the cylinder is done by a check ball and spring placed in the housing a...
Also applies to the 09-900 XL12-196 mortise cylinder coin turn.
The coin cell for the AD and CO family of electronic lock products is a 3vdc lithium. CR2025 is the specified part number.