Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ EL QEL conversion ”

RELATED FAQS

Question
Answer
What is the part number for the HD EL conversion kit for Von Duprin devices?
HD-EL conversion kit for 3 feet exit device is 050384-00 and for 4 feet is 050385-00.
What finishes should be used on exit devices near the ocean or in saltwater environments?
Von Duprin Exit Devices (33A/35A, 98/99, etc) are handled on a case by case basis regarding their ability to handle salt and chemical environments. Our powder coated finishes US28 (Anodized Alum...
Can the Von Duprin EL or QEL conversion kit be used on an old style/obsoleted (pre 2003) 33 or 35 series vertical rod exit devices?
Yes, the current conversion kits will fit the old style/obsoleted 35 or 35 series vertical rod exit devices. 
Is there a Von Duprin conversion kit to change mechanical to electric latch retraction EL in the field?
Followings are the list of the electric latch retraction EL/HDEL (hex dogging), QEL (quiet) kits: 114317-00 QELA Mod. Conv. Kit 040061-00 QELA Mod. Conv. Kit...
Can the electric strike be used with a vertical rod device on a fire-rated door?
The 6111 electric strike can be used only on non rated openings less bottom rod with pullman top latch (use ES prefix when ordering device). Device back set will change to match the centerline of t...
Not for use in fire rated openings.
How many Von Duprin QEL devices can be connected to a power supply?
Product Ordered after 7/10/2012 - Product identified by label on QEL motor You no longer need to use the 900-2Q option board (no longer available) with the PS900 power supplies to ...
Product Ordered before 7/10/2012 - Product identified by no label on QEL motor. You must use the 900-2Q option board with the PS900 power supplies to operate the QEL devices.  The attached ta...
Can you cut the EL conversion kit - 3' base plate to fit a 30" 9947 device?
You need to order the EL98/9947 or 3'  EL conversion kit.  This will fit on 28 1/8" minimum door opening on two vertical x vertical rod device doors.
Can the CD and EL options be provided on the same 98 /99 rim or vertical rod exit device?
There is not enough room for both options as the dogging mechanism in a standard cylinder dogging and the electronics for the EL or QEL options are both located at the end of the base plate. For 9...
Will the 900-2Q option board operate an EL device?
The 900-2RS is recommended to be used with EL devices but if you have a 900-2Q with PS914 power supply it can be used to operate up to two EL or one EL and one QEL devices .
Is there an EL conversion kit for the Falcon 2390 exit device?
There is no EL conversion kit for a 2390, the device will need to be replaced.
What is (SD) Special Dogging?
SD is Special cylinder dogging in the center case of 98/99 rim and vertical rod non fire rated devices and is available with standard, EL, QEL, CX and ALK.
Why is my latch not retracting when I depress the push pad on an XP98/99 device?
  Pushing on the push  bar or activating the EL/QEL or the trim on Von Duprin XP98/99 exit device does not retract the latch, it releases the latch only. Door must be pushed or pulled when device o...
Can the EL conversion kit be used on the old Von Duprin 33/35 exit device?
You cannot convert the old Von Duprin 33/35 rim exit device to EL electric latch retraction as the device center case was different than EL33/35 rim center case assembly.
Can QEL and RX be added to an existing 9927?
The QEL conversion kit (3' or 4') and the RX switch kit (050251-00) can convert the 9927 to QEL-RX9927 device.
Will the MPB-842 or MPB-840 power EL or QEL devices?
The old MPB842 power supply will power up to two EL electric panic bars but will not power the QEL devices.  A defective potted module inside the electric panic bar or defective power supply coul...
Do we offer HD-QEL?
We offer a couple different HD-QEL options:Hex key dogging (HD) is now available with Von Duprin non fire rated QEL33A/35A/98/99 electric exit devices that were shipped after De...
What are the Von Duprin part numbers for RX, LX and RX,LX-LC switch kits for field installation?
The attached table shows the part numbers for LX-RX and LX-RX-LC switches field installed.
Does Falcon offer an EL conversion kit for the 24 and 25 series exit devices?
Yes, part numbers for Falcon electric latch retraction EL conversion kits are as follows: 650147 for a 3' device. 650148 for a 4' device. 
Is the EL wiring adapter needed for QEL?
The EL wiring adapter is not needed for QEL devices.
Is there a conversion kit to add Electronic Dogging (ED) or Electric Latch Retraction (EL) to a 1690 or 1790 in the field?
There is no conversion kit to add EL or ED to an existing 1690 or 1790 series device. All of the components are built into the device, since the device does not have a separate baseplate.&n...
How many times can an EL device be operated when using a PS914-2RS with battery backup?
The Von Duprin PS914-2RS retracts the EL or QEL device approximately 200 times with five second hold time after each pull.
Can the Von Duprin EL option be added to any existing 98/99 device?
The Von Duprin EL option can be added to any existing 33A/35A, 98/99 series exit devices. 
Does the QEL device come with the EL wiring assembly?
Yes, the QEL device includes a cable assembly part number 110388-00.Since 12/2014, that cable comes in a package (part 116549) with the long cable mentioned above and the small cable that plug...
Can you convert the EL33A/35A or EL98/99 series exit devices to the QEL devices?
The Von Duprin EL33A/35A/98/99 devices can be converted to the QEL devices by getting correct sized QEL conversion kit and a 900-2Q option board for the PS914 power supply. 3' Conversion Kit #05...
Is there a conversion kit to make 94/95 devices into a QEL?
Kits are available per the following criteria.    Product Bulletin Required Series 94 or 95 Fire or Panic 3FT/4FT or 2 ft 6 in / 2 ft 10 in Finish  Optional LX...
Can a Von Duprin EL device be converted back to mechanical?
An EL device can't be converted to mechanical device. If the device is not connected to the power supply, it would function mechanically but no mechanical dogging option.