Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ door closer for pressurized doors ”

RELATED FAQS

Resolution: The part number is: 1461-3071 for the door closer cylinder body.:

Resolution: All the templates can be found at us.allegion.com Please click here :

Resolution: The 62A shoe is used when it is necessary to install the door closer (lower) down on the door so that it will operate under accessories such as overhead stops, coordinators, etc.:

Can the 4630/4640 cylinder only be replaced?

Resolution: The 4040(XP) door closer can be used as a temporary replacement in a 4630/4640 operator to provide manual control of the door while the 4630/4640 closer cylinder is being repaired or a replacement ...:

Can you manually pull a 4040SE out of hold open?

Resolution: The holding force on an SE/ME Series door closer is approximately 35 lbs. and they can be manually pulled out of hold open with approximately 35 lbs of force. :

What are the dimensions of the SC70 footprint

Resolution: The measurements from center line to centerline of the mounting holes are 2-3/8" x 6-3/4".:

Can a 4010 be mounted with swing clear hinges?

Resolution: Locate closer and arm from the centerline of the swing clear hinge pin.:

What special template (ST) is used with the 2030 closer and a low profile track and roller?

Resolution: The 2030 closer requires a minimum 1-3/8" top rail on the door for the standard track. For a top rail less than 1-3/8" and as narrow as 1", you could use the l...:

In what direction should the hold open nut be pointing for a 4041 H closer, up or down?

Resolution: Make sure that the hold open nut is not on upside down. The orientation of the hold open nut depends on the mounting. On a Top Jamb "Push Side" mount, the hold open nut would poi...:

What are the Rod and Shoe lengths for 4000 and 1000 series closers?

Resolution: STANDARD ROD AND SHOE: 4020, 4031, 1460, 1260, 4640, 4820 is: 8 3/8” (obsolete product 1520, 1370, 1070 had same length)LONG ROD AND SHOE: 4020, 4031, 1460, 1260, 4640, 4820 is: 12 3/8” (obso...:

What arm can I use for the old LCN 4030/4130 closer?

Resolution: The old 4030/4130 closers and arms are obsolete, there is nothing to replace them. No arm from other closers will fit There is no closer that can replace the old 4030 series closer with the exa...:

Is there a retrofit closer available for the obsolete 303 OHC closer?

Resolution: The LCN direct retrofit for the Obsolete 303 OHC closer was the 330 series, it was discontinued in 2009. The 3030 closer door closer body can be used as a replacement cylinder. :

Is there adjustment limits on the regulation valves of LCN manual closers?

Resolution: The regulation valves are designed to adjust the flow the hydraulic fluid in the closer which regulates the door closing speed through various phases of the closing cycle. The regulation valv...:

Does LCN sell a coupler to stack two 4040XP closers together?

Resolution: LCN does not recommend this type of installation, and has never sold a coupler to do this.:

What is the maximum degree of opening you can template a 4110 Cush closer?

Resolution: The 4110 Cush closer can be templated for 85°, 90°, 100°, and 110° maximum as standard templates.The 4110 if ordered by ST-3220 will allow templating to 135°:

What special template (ST) is used with a 4110 closer and GJ90 series?

Resolution: ST-2730 is used with a 4110EDA closer and GJ901-904 overhead stop.This can only be used with GJ901-904.If a drop plate is required, a 4010-18 drop plate would be used (A 4110-18 drop plate can not ...:

Does LCN still make a closer that has the built in smoke detector?

Resolution: The SED/MED series closers were discontinued in 2000. The SE or ME series from LCN can be used as replacements to provide a hold open feature, but will not have the smoke detectors a...:

Can I use a Glynn Johnson 410 with a 4040 regular (pull side) mount?

Resolution: ST-1630 is required when mounting a 4041 or 4040XP door closer regular (pull/hinge) side with a concealed GJ100 or GJ410 series over head stop.This ST also REQUIRES the use of a 4040-18TJ drop plat...:

Does the old style 4030 have the same templating as the new style 4031?

Resolution: The old 4030 series was: Handed Mounted regular arm hinge side. Had sized springs, were not adjustable. The 4033 is an obsolete closer. If required, handing can be verified by looking at ...:

How do you order a Senior Swing header for a 2810 on one leaf and a 2010 on the other?

Resolution: LCN does offer a 2810 Senior Swing / 2010 manual closer combo for a pair of doors. Both units contained within the same Senior Swing header. To order a paired operator with a 2810 o...:

What is the minimum top rail needed for the 4111 EDA/HEDA?

Resolution: The minimum top rail required to mount a 4110 closer is 5-1/8" measured from the stop of the frame.If the top rail is less than 5-1/8" the 4110-18 drop plate is required. Minimum 2” top rail m...:

Can you get a metal cover on a 1461?

Resolution: A designer series metal cover is an option with the 1460 series closer, the part number is, 1460-72DS1.Adapter Kit used to mount cover to the closer – part number: 1460-3373. ...:

Can you mount a 4011 as a parallel arm like the 4111?

Resolution: The 4011 can only mount on the Pull Side of the door and the 4111 can only mount on the Push Side of the door. Differences - The 4011 and the 4111 cylinders are different and the pinion shafts are...:

Can a pull side mounted 1460 open 180°

Resolution: A 1260 Pull Side can be mounted standard template for 180°, frame and trim permitting.:

How do you adjust a door closer?

Resolution: How to: What are the steps to adjust a door closer? Facts: All LCN and FALCON door closers will have 3 regulating valves and a spring adjustment. All closers with a "Del...:

What do I need to do to make my 4041 Reg/PA a hold open arm?

Resolution: When placing an order for a 4041/4040XP Rw/PA with hold open, it would be ordered as a 4041 /4040XP Hw/PA. For an existing Rw/PA requiring the addition of a hold open function, a hold open arm woul...:

What is a 4430 / 4330?

Resolution: The 4330 / 4430 is an obsolete ME closer replaced by the 4310ME or 4410ME Series.:

How do you install a Senior Swing 9540 on one leaf of a double door?

Resolution: Surface Mounting - A 9542 HDR2 (Double Door Header) and a 9540-18 mounting plate can be used on the active leaf. A manual closer with a PA (parallel arm) can then be installed on the inactive leaf....:

What is a 320G door closer?

Resolution: The "320G" is the # on a UL sticker attached to the arm of most LCN door closers, and is not a door closer model number. The "320G" means that the arm is not a mechanical hold open device and OK t...:

What size machine screws are used with thru bolts and a 2-3/4" thick door and a 4040 closer?

Resolution: A 4040 closer mounted with thru bolts on a 2-3/4" thick door would require 1/4-20 X 3-1/2" machine screws.:

What side of the door is the 4040SE mounted?

Resolution: The 4040SE is non handed and can be mounted on the push or pull side of the door.Installation Instructions :

Why does the arm of my 4110 EDA touch the door when it is closed?

Resolution: If the closer arm is touching the door, it is because the arm or the closer body is not templated correctly. Confirm dimensions are taken from the proper location and make corrections if needed. :

What can be done for a door that will not close against wind pressure?

Resolution: To correctly answer this question, we need to know how much more force is required to get the door closed. They could try turning the Rod & Shoe over (short side of shoe towards the hinge), or ...:

Can a 4010 be used on the push side of the door like a 4020?

Resolution: The 4010 and 4020 use the same door closer cylinder, the rod and shoe and covers are different. To use a 4010 cylinder as a 4020, you will need a 4020-79 rod and shoe and a 4020-72 cover. To us...:

What is the delay time adjustment on a Delayed Action closers?

Resolution: Regular LCN closers have "3" regulating valves for General Speed, Latch Speed, and Backcheck. If the LCN closer has "4" regulating valves, then the closer has the Delayed Action feature. De...: