Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ CAN ELEC HINGE BE USED ON NOA DOORS ”

RELATED FAQS

Resolution: Cam Lift Hinges are specially designed hinges used mainly on acoustical door assemblies. The Cam Lift Hinge lifts the door during its travel and seats the door bottom for a pos...:

What is maximum width, height and weight for IVES butt hinges?

Resolution: Butt hinges can be used on doors up to 4' wide and 200 pounds. There is no maximum door height. However, an additional hinge must be installed every 30" when exceeding a 7' d...:

What is the standard gap between a pair of doors hung with continuous hinges?

Resolution: The standard gap between a pair of doors will be 3/16" when used with a Steelcraft "Z" astragal. If a wide inactive leaf is requested (no astragal) the gap between the doors will be...:

Will a Senior Swing or Swing IQ work with swing clear hinges?

Resolution: Push Side Surface Mount Senior Swing or Swing IQ can be used with swing clear hinges, standard butt hinge/offset pivot templating. Pull Side Surface Mount Senior Swing&nb...:

Is the Von Duprin EPT10 required for CX device?

Resolution: The wires in the EPT are larger than the wires in an electric hinge and are less prone to breaking. This is why we recommend the Von Duprin EPT10 with CX device but if necessary yo...:

Can I use a Glynn Johnson 410 with a 4040 regular (pull side) mount?

Resolution: ST-1630 is required when mounting a 4041 or 4040XP door closer regular (pull/hinge) side with a concealed GJ100 or GJ410 series over head stop.This ST also REQUIRES the use of a 4040-18TJ drop plat...:

Can a 450 overhead be used on a 48" wide door hung with butt hinges or offset pivots?

Resolution: The 455 can be mounted on a 48" wide door, but we cannot guarantee that it will withstand the forces involved. Recommend using 906 instead.:

Does a SEH require a door closer?

Resolution: The SEH is an "electronic holder" (ONLY) that is used to hold open a Fire Rated opening. It requires a door closer to be mounted on the opposite side. It is normally used on an existing opening wit...:

Where is the Fire Label located on a door and a frame?

Resolution: Fire labels (UL, ITS/WHI or FM) are located as follows: Butt Hinges and Pivots: On the doors the fire label is located on the hinge edge between the top and 2nd hinge preparation. On the fram...:

What is the standard screw size used on Steelcraft doors with 4 1/2" or 5" hinges?

Resolution: Steelcraft follows the industry standards for hinge reinforcement and preparation for both door and frame. Unless otherwise specified all products prepared for butt hinges will have mounting holes ...:

What hinges can be used on tornado doors?

Resolution: The following hinges are available on Paladin series doors and frames: Butt hinges - 4 1/2" or 5" ball bearing type either standard or heavy duty Continuous hinges - full ...:

Can a 9500 series operator on the push side be used with Cam lift hinges?

Resolution: The Senior Swing will work with Cam Lift Hinges as a PUSH SIDE MOUNT 9542/9553/9563 only. Maximum 3/4" lift. Maximum 15 pounds force to push door up the Cam Lift Hinge. Cam Lift Hinges WILL NO...:

What is the difference between the FE and DE-Series frames

Resolution: A Double Egress frame is a double door frame prepared to receive two single-acting doors swinging in opposite directions (both doors are) the same hand. These openings are installed in cross corrid...:

Can a Cam Lift hinge be used with LCN closers?

Resolution: Cam Lift hinges can only be used with LCN door closers that have a "Regular" or "Reg hold Open" style arm. Locating the Closer and Arm from the centerline of the pivot point of the cam lift h...:

Can the bar style coordinators be used with swing clear hinges?

Resolution: No, the geometry of a swing clear hinge prevents the coordinator from working correctly. The bar style coordinator will not hold the active door open far enough for the inactive door to clear the ...:

Are flush bolts available on the inactive leaf of hurricane double doors with either FBC or NOA approvals?

Resolution: Ives SB360 surface bolt at top and bottom are the only flush bolts approved for use on H-Series hurricane FBC or NOA applications? The only approved latching hardware for inactive leaf of pairs w...:

What door meets FBC / NOA Zone 4 requirements?

Resolution: H-Series doors in single leaf applications with only mortise locks meet the FBC / NOA Zone 4 requirements?3070 max flushOutswing & Inswing applicationsZone 4 requires 120 to 170 psf.: