Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ Arm hitting door when closed ”

RELATED FAQS

Resolution: The 40401/4040XP closer with optional EDA arm has to be mounted parallel arm on the push side of the door.:

How do you order a Senior Swing header for a 2810 on one leaf and a 2010 on the other?

Resolution: LCN does offer a 2810 Senior Swing / 2010 manual closer combo for a pair of doors. Both units contained within the same Senior Swing header. To order a paired operator with a 2810 o...:

Does a SEH require a door closer?

Resolution: The SEH is an "electronic holder" (ONLY) that is used to hold open a Fire Rated opening. It requires a door closer to be mounted on the opposite side. It is normally used on an existing opening wit...:

Can you replace a regular arm with a hold open with out moving the door closer?

Resolution: Yes, as long as you stay with the like style arm. Example: replace an RW/PA with HW/PA, replace an EDA with HEDA, or replace a CUSH with HCUSH.:

What are Pneumatic Automatic Operators?

Resolution: Pneumatic Automatic Operators are used in areas where electrically operated devices are not convenient or permitted. Consists of a modified, heavy-duty door closer for manual oper...:

Can you mount a 4011 as a parallel arm like the 4111?

Resolution: The 4011 can only mount on the Pull Side of the door and the 4111 can only mount on the Push Side of the door. Differences - The 4011 and the 4111 cylinders are different and the pinion shafts are...:

What arm can I use for the old LCN 4030/4130 closer?

Resolution: The old 4030/4130 closers and arms are obsolete, there is nothing to replace them. No arm from other closers will fit There is no closer that can replace the old 4030 series closer with the exa...:

What is the narrowest door a 4040 pull side will mount on?

Resolution: 14" door leaf is the narrowest with standard template.:

Why would a 4600 not open a full 90 degrees?

Resolution: A 4600 (4630/4640) not opening to a full 90 degrees could be caused by a couple things: The Opening Force could be set too low. Try increasing the opening force adjustment on the contr...:

Why does the arm of my 4110 EDA touch the door when it is closed?

Resolution: If the closer arm is touching the door, it is because the arm or the closer body is not templated correctly. Confirm dimensions are taken from the proper location and make corrections if needed. :

Door hitting the strike jamb?

Resolution: If the door hits the frame (or rubs on the rabbet of the head or jamb) the frame is out of square and improperly installed. Door edge rubbing on the rabbet - shimming the hinges may resolve the...:

Why does my Chexit device open without sounding the alarm?

Resolution: :

In what direction should the hold open nut be pointing for a 4041 H closer, up or down?

Resolution: Make sure that the hold open nut is not on upside down. The orientation of the hold open nut depends on the mounting. On a Top Jamb "Push Side" mount, the hold open nut would poi...:

What do I need to do to make my 4041 Reg/PA a hold open arm?

Resolution: When placing an order for a 4041/4040XP Rw/PA with hold open, it would be ordered as a 4041 /4040XP Hw/PA. For an existing Rw/PA requiring the addition of a hold open function, a hold open arm woul...:

Can you mount a 4041 Cush arm with a EDA arm template and get 180 degrees opening?

Resolution: The dead stop post would need to be removed and the 4040/4040XP EDA mounting template for 180° would be followed.:

Do you need Double Egress arm to install a 4040SE on the Push Side of a door?

Resolution: The 4040SE uses the regular arm for any Push Side mounting (minimum 28" door width). ST-2788 (a special arm and track) can be used to mount a 4040SE on the Push Side of a smaller (narrow) doo...:

Can I use a Glynn Johnson 410 with a 4040 regular (pull side) mount?

Resolution: ST-1630 is required when mounting a 4041 or 4040XP door closer regular (pull/hinge) side with a concealed GJ100 or GJ410 series over head stop.This ST also REQUIRES the use of a 4040-18TJ drop plat...:

Will CX re-arm if door is held open?

Resolution: If a door position switch (DPS) is connected across the green and white wires of the old CX (green and red of new CX) the CX would go into alarm if the door is held open when it attempts to rearm.&...: