ad lock firmare

RELATED FAQS

Question
Answer
Information on low battery threshold and nuisance delay is noted below: New firmware now has improved levels. - These are approximate values/levels which change with measurement meters and measure...
AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 4 Battery Holder New batteries = 6.2 VDC Low battery threshold is 4.7 VDC for SM & MT - and 3.7 VDC for MAG and PROX (USB stops working at 4...
    AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 8 Battery Holder New batteries = 12.4 VDC Low battery threshold is 7.2 VDC Critical battery threshold is 6.9 VDC Coin cell = new/...
CO2004 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
CO2504 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
  CO200 & CO250 Disable coin cell Nuisance delay and blink, With CO.A.7 and SUS 4.10.2 or newer for CO200 and CO250, you can use the SUS/HHD, under Lock Properties, Edit, to de-select, DISABLE, t...
When new product(s) are added to an existing installed customer site, all devices at that site should be updated to the latest firmware revision that is available.  Whenever an AD-Series&nbs...
 
 
 
When new product(s) are added to an existing installed customer site, all devices at that site should be updated to the latest firmware revision that is available.  
 Whenever an AD-Series credential reader is upgraded with new or different credential types or replaced in the field, be sure to update the firmware so that the main and reader have com...
For the most consistence product operation all device firmware revisions should match the new product being installed.  
Ensuring consistent firmware revisions across your facility will guarantee that all of the installed customer products will act and respond the same durng use and programming.  
Products updated with the latest available firmware will also include the latest feature set(s), improvement performance and/or bug fixes  
Go to the Schlage support site to download the latest firmware package  - www.schlage.com/support  
Steps to determine what firmware version your products are currently using AND if a firmware update is suggested: Use the Hand Held Device (HHD) and Schlage Utility Software (SUS) application to...
ALWAYS put the PIM400 in LINK mode first. On a PIM400-TD2 press the LINK1 Button for door one, and LINK2 button for door 2. With a PIM400-485 you must use the SUS/HHD to select which door to LINK.  
1. To put the AD400 in LINK mode, hold down the RTE (Lever or crash bar see below) and press the # key on the key board, or present a card to the reader.            Why press the # key? Because t...
2. AD400 requires a Request To Exit (RTX) signal to link - see the user guide instructions for the linking process.  For an AD400 to enter link mode, it must see the RTX (Request To Exit) switc...
   3. Check the AA battery level, if the AA batteries are below 4.7 volts the AD400 can fail to LINK.             Install fresh batteries, with a level of 6.0 volts or better.  
4. PIM400/AD400 COM400 plug could be damaged! The small pins in the Main PCB board connection for the RF COMM board can get bent during installation of the RF COM400 board. If the PINs are bent a...