ND for thick door

RELATED FAQS

Question
Answer
Schlage ND-Series tailpieces for extended doors are available by only two means, but are not available to order separately. If an extended tailpiece is needed, then a complete lock will need to ...
The standard out-of-the-box ND lock will fit the following door ranges: All functions except ND85 will fit onto a door 1 5/8" through 2 1/8" extended equally. The ND85 will fit on doors fro...
The 8190 can be order as a standard for 2 1/4" door thickness. Specify the door thickness to get proper mounting hardware.
The 09-611 indicator stands off the door 0.39".
The pricebook suggests (for a 1-3/4" door) using a 1-3/8" cylinder when installing with an 09-611 occupancy indicator.
Hinge backset is the dimension from the leading edge of the hinge to either the stop on the frame or to the stop face (push side) of the door. For operating clearance, the hinge backset on the d...
The minimum door thickness that the AD or CO series lock will mount on is 1 3/8".  Be advised that this will require additional spacers to be ordered separately to allow the lock to mount...
Most locks will have a standard door range they will install on, but occasionally customers will want to use them on thicker doors.  In order to do so, the extended door thickne...
The easiest method to obtain an AL lock for a 2" door is to specify a 2" thick door when ordering.  
Part required by function:2 each A700-043 driver & A700-034** lever insert in addition to the chassis parts below:AL10S – 2 hubs A700-028AL25D – 2 hubs 1 A700-028 (inside), 1 A700-030 (outside)...
31252U provides the 3125 knocker and the U701 viewer for 1 5/8" - 2 1/8" thick doors.
The L9000 lock can be ordered for doors greater than 1 3/4" thick.  The allowable door thickness is dependent on the L lock function and how the lock is extended.  All locks for exte...
Currently, the 914KIL trim will only work on 1 3/4" doors.
B500 with standard cylinders How to order with the deadbolt: Door thickness over 1 3/4" to 2 1/4", specify door thickness when deadbolt is ordered Door thickness greater than 2 1/4" will req...
Standard mounting packages are only for a 1 3/4" thick door. Door thickness other than 1 3/4" need to be specified when ordering the device.
Standard 98/9947 works on 1 3/4"- 2 1/4" thick door.
Standard Schlage rim cylinders will fit a total thickness of door and projecting trim of 3 inches, this includes a minimum of 3/8" of engagement of the tailpiece into the exit device.  See ima...
For total thickness measurements larger than 3 inches see the special cylinder offerings in Pricebook.  Specify the part number and include the total thickness.  We do not offer the ...
All Steelcraft doors are a nominal 1 3/4" thick. Special door thicknesses are not available.
A 4040 closer mounted with thru bolts on a 2-3/4" thick door would require 1/4-20 X 3-1/2" machine screws.
1 3/4" is the standard door thickness. Steelcraft only makes a nominal 1 3/4" thick door. A 1 3/8" was made for light duty commercial applications but that product was discontinued in 1999.
The standard door range for a B600 is 1-3/4" to 2".  This includes Standard cylinder, Full Size IC and Small Format IC. Non standard door thicknesses include the following and are availa...
Use the 575-2 strike with 9975 device on a pair of 1 3/4" thick doors with overlapping astragal mounting on the exterior of the active door. The strike lip has been cut off to eliminate any interfe...
Window kits are available for Steelcraft doors as either factory installed or prepared and installed by a distributor. Factory prepared light cutouts are supplied with Dezigner trim as st...
Levels and Models (covered in ANSI A250.8 (SDI 100) "Recommended Specifications for Standard Steel Doors and Frames") are SDI term aid in the selection and specification pr...
The B600 (standard cylinder only) can be be specified for 1 3/8" thin doors and the appropriate parts will be supplied.  Interchangeable cores are not available for 1 3/8" thin doors.
The outside housing, B600-089, can be ordered to retrofit an existing standard cylinder B600.Description: 1 1/8” Collar (trim ring) for 1 3/8” – 1 5/8” door
If the lock has not been ordered then specify a door thickness of 1 3/8" and a shim kit will be provided to allow installation on a thin door. If the lock has already been ordered then order the A...
A 1 1/4" mortise cylinder with straight cam (similar to the Schlage B502-191) or a 1 1/2" mortise cylinder with straight cam using supplied spacer collar. Cylinder length does not chan...
Specify how the door is extended and the door thickness.  Pricebook availability: D knobs ordered for Extended Equally (EE) and Extended Differently (ED) doors over 2" up to 2 1/2"...
The AL series lock fits up to 1 7/8” door thickness out of box.
The ND lock can be installed on a 1 3/8" thick door by utilizing spacers, part number XN12-012.  These spacers are included with the lock when ordered for a 1 3/8" thick door.  The spacers can be o...