Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
where are Hollow metal installation instructions
”
RELATED FAQS
Question
Answer
Can out of plumb (twisted) frames be adjusted?
Resolution:
Out of plumb (also referred to as twisted) frames usually cannot be adjusted."Out of Plumb or Twisted frames (or jambs)" is a condition created by improper wall construction and/or improper in...:
What is thermal bow?
Resolution:
Thermal Bow is a temporary condition which occurs in metal doors mainly due to the temperature differential from one side of the door to the other. This may occur in exterior doors when direct sun ...:
Why are frames grouted?
Resolution:
Grouting frames is: A process done in the field during hollow metal frame installation The internal cavity of the frame is fill with masonry or mortar It is intended to mainly provide ...:
Can wood doors be used with with double egress frames?
Resolution:
Yes, wood doors can be used and installed in most hollow metal frame applications including FE-Series and DE-Series Double Egress frames. Caution - For fire rated applications the wood door manufa...:
Can Steelcraft make a 12 gage hollow metal mullion?
Resolution:
Steelcraft does not manufacture 12 gage closed section mullions. The maximum is 14 gauge. Steelcraft can provide the outer perimeter (open sections only) of a transom frame in 12 gage material. ...:
Where can I find templates for the 237L two point latch device?
Resolution:
Click HERE for the instruction and template for 237L device.:
Steelcraft field paint instructions
Resolution:
Steelcraft frames and doors are furnished with a high grade, low gloss, baked-on prime paint that provides the best possible protection against corrosion, abrasion and weather, and is an excellent ...:
Where are the PS914 instructions?
Resolution:
The link to the specific sheet can be found by clicking here: http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/InstallInstructions/Von_Duprin_PS914_Power_Supply_Installation_I...:
What is the 022558-000-70?
Resolution:
The Falcon T series was discontinued August 12th, 2026 and was replaced by the Falcon TM series. DISCONTINUED: The Falcon T lock had a reinforcement kit for a 1 3/4" thick hollow metal do...:
What are the installation tolerances for hollow metal frames?
Resolution:
Industry standards for hollow metal frames installation tolerances have been developed by both the SDI (Steel Door Institute) and HMMA (Hollow Metal Manufacturers). Both standards are based on th...:
Can "toed in" or "toed out" jambs be adjusted?
Resolution:
This condition (toed in or toed out jambs) is usually not found until the door is installed.Frames which have toed in or toed out jambs have been installed out of tolerance.It is the responsibility...:
Why do frames rust out fast?
Resolution:
Excessive premature frame rusting is caused by improper jobsite installation practices and most likely caused by the following circumstances: :
Hollow Metal price estimates
Resolution:
Pricing information is not a part of the Knowledge Center data. For all hollow metal price comparisons please e-mail the Steelcraft Estimating Team. For your reference, the e-mail address...:
Does Steelcraft have frame installation instructions?
Resolution:
It is always recommended to point installers to the industry installation manuals which are very comprehensive and are ANSI documentsClick here to get the updated link to the Steelcraft Shop M...:
What is ASTM E-119?
Resolution:
ASTM E-119 is a test standard for walls, partitions and floor or roof systems: This test standard is also used for ceramic type glasses when used as window wall and/or borrowed light frames.As...:
What do you do if rust spots show up on steel doors and frame material?
Resolution:
During the construction cycle, spot rust is usually attributed to either material handling damage or improper storage of the material on the jobsite. The material must be repaired and repainted as ...:
Can out of square frames be adjusted?
Resolution:
It is the responsibility of the installing contractor to install all material in accordance with SDI or HMMA installation standards and tolerances. Out of square frames which are installed out...: