Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ What series on mortise lock outside lever is always fix ”

Resolution: There are two ways to replace the outside lever for a Schlage L9000 mortise lock. Replacing the outside lever only with part number 09-401 is possible, but very difficult....:

Why does my AD or CO series lock unlock when the lever is raised?

Resolution: Installers have reported that their AD-CO Series cylindrical or mortise locks will unlock whenever the outside lever is lifted. This will occur if the outside spindle (square post) is install...:

Is 630 Stainless Steel finish available on the latitude lever for Falcon MA series mortise locks?

Resolution: The following lever designs are not available in 630 finish with Falcon MA series: Latitude, Longitude, Broadway, and Boardwalk :

What is the part number for the lever return spring for the old M series mortise lock?

Resolution: Falcon is reintroducing the lever return spring for the discontinued Falcon M mortise series. Effective November 1, 2014 the lever return spring is now available for purchase with a list pric...:

What other locks can the blue lever removal tool 24002693 be used with?

Resolution: On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project. This tool can be used for Schlage ND-Series ...:

Does Schlage make a mortise lock that the lever on either side retracts the latch and a key on either side retracts the deadbolt?

Resolution: The L9466 Store/Utility Room lock can provide this functionality. Operation: Latchbolt retracted by knob/lever either side. Deadbolt thrown or retracted by key from either side. When the deadbolt ...:

Will the L9485 or L9486 operate without a hotel cylinder?

Resolution: Putting a standard non-hotel cylinder in a L9485 or L9486 will change the operation of the lock to the L9480, storeroom lock with deadbolt.:

Explain the function for the L9485.

Resolution: L9485: Latchbolt retracted by key outside or by knob/lever inside. Outside knob/lever always fixed. Deadbolt thrown or retracted by inside thumbturn. When deadbolt is thrown, all keys become ino...:

What cylinders are used to operate Von Duprin devices?

Resolution: If unclear whether mortise, rim, or key-in-lever is needed, reference links below to determine what cylinder type is needed. In order to determine cylinder type n...:

Is there a round corner armor front for the L series mortise lock?

Resolution: The L series armor fronts are only available with square corners. :

What is the Multi Point LM9300 Series?

Resolution: MultiPoint locks are three-point locking systems that secure the door at three points – top, bottom, and traditional center latch location. Operating just like traditional locks, MultiPoint locks...:

What is the replacement for the Locknetics 9100 series electric strike?

Resolution: The Locknetics 9100 series electric strikes are replaced with Von Duprin 6211 and 6210 electric strikes. The 6211 is used if the frame is being replaced. The 6210 is for ...:

How to build an L-Series chassis.

Resolution: This Step-by-Step guide is specifically designed for the functions listed below, however, it can be referenced with a majority of L series functions since most of the parts are ...:

Are ND locks available in 629 or 630 finishes?

Resolution: The AL and ND locks are not available in any stainless steel finishes. The only option is either the 626 satin chrome or 625 bright chrome.:

Are parts still available for the old Falcon M locks?

Resolution: Related solution: What is the part number for the lever return spring for the old M series mortise lock?:

Is the 375L the only trim that will lock with a lever for the 5575?

Resolution: The 375L is the only lever trim with 5575 mortise device that locks or unlocks the outside handle.:

Why doesn't full rotation of the AD or CO Series Exit Trim (993) outside lever fully retract the Von Duprin 98/99 Exit Device latch?

Resolution: - AD Series and CO series products require that the Night Latch (NL) screw is installed in the exit device. Be sure this screw is installed- Exit hardware and strike must be properly mounted ...:

What is the ME9453?

Resolution: At one time we offered a 9453 function in several different lever, knob and grip handleset designs. A wide variety of trim offerings were available. The mortise lockcase was a smaller version of th...:

How does the 98-2 or 99-2 double cylinder function affect the outside lever trim?

Resolution: Double cylinder (-2 or -2SI) features an inside key cylinder which locks or unlocks the outside trim and an outside key cylinder which retracts the latch bolt only (Night latch function). Thi...:

Is there an exit lock offered in the ND series?

Resolution: The ND12 and ND25 are both exit locks.ND12 Outside lever always fixed. Insidelever always unlocked for immediateegress.ND25Blank plate outside. Inside leveralways unlocked for immediate egress.:

What is the difference between the classroom and storeroom functions?

Resolution: ANSI F84 Classroom Lock Outside lever locked and unlocked by key. Inside lever always unlocked for immediate egress. ANSI F86 Storeroom Lock Outside lever fixed. Entra...:

What is the part number for the inside lever on an L9000 lock?

Resolution: The part number is the 09-402, specify the design and finish.:

Can you order the Schlage L series mortise lock with knob on one side and lever on the other?

Resolution: Includes the SL1 lever on one side and the SK1 knob trim on the other side.:

How do I change the function of the Von Duprin 7500 mortise lock from Lever ( classroom ) to NL ( night latch )?

Resolution: To convert the Von Duprin 9975L to 9975NL exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory): Turn the NL screw on 7500 mortise lock counter clo...:

Does Falcon have a breakaway lever trim feature on mortise locks?

Resolution: The MA lock does not have Vandlgard or a breakaway trim feature, however, the lever spindle on the MA lock will shear if too much force is applied in order to prevent internal lock damage and resis...:

Why does my lever sag on an L9000?

Resolution: Levers may sag due to an incorrectly installed springcage or an incorrect springcage.Mortise locks with a fixed (rigid) lever such as an L9080 will use a spacer on the rigid lever (outside) and a s...:

Why can't I order an AD-Series or CO-Series mortise deadbolt with a classroom/storeroom (70) function

Resolution: * NOTE: the AD300/400 devices simply communicate the change in Deadbolt Position status to the Host software. The software then decides what action should or should not be taken at the device. :

What is the part number for the lever return spring for the MA lock?

Resolution: Lever assemblies part numbers are found in the Pricebook. Note they are handed.:

Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ What series on mortise lock outside lever is always fix ”

RELATED FAQS