what is sus/hhd

RELATED FAQS

Question
Answer
Customers should maintain their Schlage Utility Software at the latest version that is available.  This ensures that they have the latest features available and will be compatible with current...
Follow the link to the Schlage Technical Support page and find at the bottom of the page under "AD-Series Accessories" the Schlage Utility Software Update Guide,&...
Updating the Schlage Utility Software (SUS) on a Hand Held Device (HHD) will cause the SUS "Login Password" AND the current device "Coupling Password" to be reset to factory default settings of - 1...
The Request to Exit (RTX) switch input can be used as a remote door release.
A single-pole, single-throw switch (e.g., pushbutton switch) must be connected across the RTX input pins.
When the switch changes state (e.g., from open to closed), the CT5000 will change the state of the Strike relay.
Look to see if the  "Fail Safe?UNLOCK" on communication failure is set and you have lost communication.
The "Unlock on READ" from diagnostics will clear with the next AD400 heartbeat, automatically. It will also clear with successful communication to a working access control panel. 
 If the AD-400/AD-401 is LINKED to a PIM400-TD2 and all credentials including invalid cards are granted access, the PIM400-TD2 is not communicating with the Access Control Panel, and the lock is st...
Or force a strike input to the PIM400-TD2. Short J8-1 and J8-2 (Door 1), Short J7-1 and J7-2 (Door 2) on the PIM400-TD2
-         With the CIP NOT inserted and the Schlage Utility Software (SUS) running o   Enter the Master Programming PIN or Present Loc...
Once a user changes the SUS coupling password , the previous SUS coupling password is also saved by the SUS program; this allows the user to update multiple locks with a new Coupling Password witho...
The Coupling Password update is automatic; whenever the Schlage Utility Software, with a new Coupling Password connects with a device, the Schlage Utility Software will automatically update its old...
The internal process to couple a device with new SUS password is described as follows: the SUS first tries to couple with the current password.  If that fails, the SUS tries to couple with the prev...
To verify that the device/lock is coupled; click on the SUS device options-> Couple HHD to device , a message will pop up confirming that the device is already coupled.  
After updating the SUS coupling password, subsequent HHD’s will need the new coupling password entered before they can update any information in the lock, once the HHD has the correct coupling pass...
Make sure the lock AA batteries are good. 4.8 VDC or higher.
When in its “Active state”, the mechanical key switch can prevent USB connection. Make sure the lock key cylinder and tailpiece are properly installed.
Make sure the mechanical triangles on the back of the outside escutcheon are aligned properly.  See the installation instructions at www.schlage.com/support Schlage Technical Support.&nbs...
If the Schlage Utility Software pops up a "E201 error", just ignore it, and tap "Device Options" or update your firmware. See 78451  
Make sure the HHD/SUS is set to USB communication by checking the small icon right of the "No Device Connected" message.  The symbol should be a USB symbol when working with USB enable product...
With the new FW package 2.19.0; AD300 FW 2.17.0 and AD400 FW 2.17.0 (released 09/23/2011) the firmware looks for a motor clutch switch change after a motor move command. If there is no motor clutch...
If the triangles in the spring cage spindle are not aligned properly the motor will not move enough to change the clutch switch. Is is very likely with a lock on the bench; but a properly install...
When the new firmware moves the motor three times without seeing the clutch switch change it reports to the SUS diagnostics that the motor is stalled. Aligning the triangles will let the motor move...
If the lock is mounted on the door, it is necessary to adjust the mortis/cylinder tightness and spring cage tailpiece alignments, making sure there is no binding or stopping of the spring...
Just align the triangles per the installation instructions to allow full motor movement.   - This will eliminate the SUS motor STALL report. - This will eliminate the three ...