what does "Cush" mean?

RELATED FAQS

Question
Answer
The 4110-18, and 4110-18 CUSH  drop plates are identical. The difference between a 4110 EDA, and a 4110 CUSH is the templating on the door. That is why you order them differently, to...
The design change went into effect on 6-16-2011.  The stop is now removable and can be changed from one side of the shoe to the other, which makes it a non-handed arm.  All arms are shipped standar...
This engineering change did affect the templating of the closer. The stop in the shoe is slightly larger than the original handed cush shoe. The new non-handed arm template locates the closer and s...
The part number for the Spring Cush block assembly is: model number-3080. EXAMPLE: 4110-3080
The 4040 XP CUSH/EDA can be mounted on a Flush Transom frame by using a -419 Flush Panel adapter.
It would be unnecessary to use the CNS/Cush arm and the Glynn Johnson overhead devices in the same application, both mechanisms stop the door.
The 4110 Cush closer can be templated for 85°, 90°, 100°, and 110° maximum as standard templates. The 4110 if ordered by ST-3220 will allow templating to 135°
For LCN Cast Iron Closers, the 4050A, and Falcon SC closers it is (1 3/4") wide, (1 1/2") tall and (1 1/2") deep For 1250 and 1450 LCN Alum body Closers it is (2") wide, (1 1/2") tall and (1 1/2"...
ST-3195 is used to obtain the old style EDA or Cush arms which were assembled with threaded studs so that you could take apart the arm assemblies. Our current standard EDA and Cush arms are rivet...
SCUSH,
HCUSH, PA Mount, Parallel Arm Mount
SHCUSH,
EDA ARM - The EDA arm is a heavy duty parallel arm mount.  The degree of door opening is determined by the template used for mounting. EDA arm closers can only be mounted as a Push Side parallel ar...
Cam Lift hinges can only be used with LCN door closers that have a "Regular" style arm.             Manual Closers: Maximum li...
Yes, as long as you stay with the like style arm.  Example: replace an RW/PA with HW/PA, replace an EDA with HEDA, or replace a CUSH with HCUSH.
The hold open position on a "REG" or "EDA"  hold open arm is set with the door to a few degrees shy of the desired hold open point. To properly set, open the door 5° less then the desired hold open...
BSS means - Blade Stop Spacer.  A -61 for example would be used after the series of the closer being used. CSS means - Cush Shoe Support. A -30 for example would be used after the series of the cl...
  How to:  What are the steps to adjust a door closer?   Facts: All LCN and FALCON door closers will have 3 regulating valves and a spring adjustment.  All cl...
The 1460 Regular Arm part numbers are: Regular Arm -- 1460-3077 or 1460-3077L for long arm (must specify finish). Regular Arm with PA -- 1460-3077PA (must specify finish). Regular Hold Open Ar...
The dead stop post would need to be removed and the 4040/4040XP EDA mounting template for 180° would be followed.
The 4040/4040XP closer mountings have the following maximum opening degree templating: The 4040/4040XP PA "Regular Arm" mount will allow for 180° max. opening. The 4040/4040...
The 4040XP/4041 Cush and HCush (Hold Open Cush) use the same instructions / template.
The part number for the 4041/4040XP HCush arm is 4040XP-3049CNS.
The 4110 hold open spring Cush (Spring H Cush) arm part number is 4110-3049SCNS.
When using the 4111 with a bar style coordinator MB-mounting brackets ordered from IVES are required. The brackets wrap around the coordinator to provide a surface for mounting the parallel arm ...