von duprin pneumatic parts manual

RELATED FAQS

Question
Answer
The sequence card part number is 3426 and plugs in the "S" slot of a control boxes right next to the 10 pin terminal strip. The 7902/7902ES or 7982/7982ES can be converted to a 7902S/7902SES or 79...
The Von Duprin Pneumatic PN98/99 series exit devices feature provides remote latch bolt retraction in hazardous areas where electrically operated devices would not be permitted.
The Von Duprin Pneumatic or "PN" device was designed for Intrinsically Safe Class 1, Division 1 applications.
4810 series is a Top Jamb Pull Side application. 4820 series is a Top Jamb Push Side application. 4840 series is a Parallel Arm Push Side application.
The 4840 and the 4810 are they only cylinders that can be interchanged, they use the same cylinder for their individual applications.
If using the LCN pneumatic control box as the air source for the Von Duprin Pneumatic devises then you have to use the LCN 925 tubing because of the size of air line fitting on the LCN co...
The Von Duprin EL option can be added to any existing 33A/35A, 98/99 series exit devices. 
The Von Duprin 6000 series electric strike can be converted by ordering the appropriate kits below.  Kits include the solenoid, plunger, spring, and washer. 6000 Series solenoid Kit 12VDC -...
Changing the handing on a Von Duprin 373L trim requires following parts on all lever designs EXCEPT #12: RHR requires part number 090092-00 (LEVER CONTROL SPRING RHR PKG/4) and 050597-...
Please see the Maintenance Kit Manual for information on device lubrication as well as complete breakdowns and parts lists for Von Duprin exit devices.Exit devices and latc...
A B663 exploded view can been found here.
Falcon (19. 24, 25, and XX) parts manuals for Exits are downloadable on the 
Von Duprin has a maintenance kit part number 050046-00 and maintenance instruction, part number 941079-00 for 98/99 series devices. There are some common parts between 98/99 series and 22...
Followings are the steps to convert the Von Duprin 88TP to 88L device. Need to replace the back plate on the 88 exit device, part number 050103. Order a 373L trim and specify handing. Recomme...
To convert the Von Duprin 6000 series electric strikes from FS to FSE  or from FSE to FS follow these steps: Remove the electric strike face plate. Remove the strike box cover pl...
Part numbers: FS slider, part # 970387 (6211WF/6212WF/6221/6223 only) FS slider, part # 970388 (Except 6211WF/6212WF/6221/6223) FSE slider, part # 970388 (6211WF/6212WF/6221/6223 only) FSE sl...
 Pneumatic Automatic Operators are used in areas where electrically operated devices are not convenient or permitted.  Consists of a modified, heavy-duty door closer for manual oper...
Number of reasons could Von Duprin 55 or 88 series cross bar to sag. Attached are the reasons that could cause the cross bar to sag or not lift. The hinge case spring lifts both lever arms and t...
The pneumatic operators are designed to function with an input air pressure to the 7901/7902 Series control box of 80 (min) 100 (max) PSI, and an output pressure of 60 to 80 PSI to the pneumatic (2...
PN33/35/98/99 Pneumatic exit devices are not usually used with RX or LX switches since the Pneumatic PN device is used instead EL to eliminate the electric from the device.
The maximum 925 tubing run length from the Control Box to the Door Closer is:  7980 Series Control Boxes --- 50 "Linear" feet from Control Box to Door Closer.  7900/7940 Series Control Boxes --...
The circuit board is sometimes referred to as a "module" in the field.
The 050535-00 replaces the old Von Duprin EL solenoid part number 971687. 
A 3' exit device can not be modified to a 4' exit device. You will need to replace the device with a 4' one.
The Von Duprin CD kit comes with the cover plate machined to accept the cylinder dogging mortise cylinder.1 1/4" mortise cylinder with an inverted straight cam is required for CD option on Von Dupr...
Order E-Trim Mech Kit  part #050671-00 which will include a new solenoid already mounted to the blocking mechanism. See installation instruction # 921297 here which will show how to remove block...
The rim cylinder with thumbturn, XB11-979 (Figure 1) was designed to be installed on the inside head of the Von Duprin 98/99–2 double cylinder exit devices, see Figure 1. The rim cylinder with...
End cap without end cap bracket is 968601. End cap kit with bracket is 900981 End cap bracket is 971795-89
You must have the Von Duprin NL Cylinder plate part number 967484-89 to convert the 370 series controls from classroom function to night latch function. If new installation, use the NL cylinde...
A E996 conversion kit is required to convert the 996L/L-BE trim to E996L/L-BE electric trim. 050672-00 is the electric conversion kit for 996L rim or vertical rod exit device. 050673-00 is the ...
To add the bottom rod and latches on 8827LBR it requires Bottom Rod Kit part #050455-XX 8827 Rod Guide Kit part #50482-XX 8827 LR Bottom Latch Kit W/Cover part #050467-XX 304L Bottom Strike
113781 is the part number for Von Duprin 15 second CX sign.
Part number for Von Duprin standard 15 sec. release Chexit module shipped after 8-24-2015 with motor driven is 040086-00. Part number for Von Duprin standard 15 sec. release Chexit module shi...
This solenoid is replaceable and the part number is 050671.
The part number for Von Duprin exit alarm ALK board is 101030-00.
The Chexit device has a different base plate and center case than the ALK.  The Chexit device would need to be replaced with an ALK device.
The part number for 88 series dogging screw is 090004 (package of two) and 090083(package of ten).
HD-EL conversion kit for 3 feet exit device is 050384-00 and for 4 feet is 050385-00.
All Von Duprin exit devices (22, 33/35A ,55 ,88 ,95 and 98/99) use 5/32" dogging key. There are two part numbers available: 090005 is the package of 2 and 090085 is the package of 10.