rim cylinder length

RELATED FAQS

Question
Answer
There are different mortise cylinder length options depending on the cylinder type. Below is a list of available options for conventional, FSIC, and SFIC cylinders, as well as the convent...
The existing 373L control was modified and re-named as 379L to allow us to use the 55 rim device on an ADA door opening.  The 379L control is our 373L with different hex ...
Key-in-lever tailpieces differ in length depending on the lock series, function, and design.  Click here to identify the tailpiece and length.  NOTE: Modular cylinders use...
Click here for a list of available Schlage cams comparable to the Sargent 13-0660.
These cylinders are designed with a microswitch attached to the back of the cylinder. The switch is operated by a cam when the key is rotated.   To order: XB09-195 Mort...
The XB09-195, XB09-795, and XQ11-804 are basically modified mortise cylinders. The overall length of the mortise cylinder switch is approximately 1-9/16" (1.563"). The diameter of the cylinder face...
The Sargent cams listed below work for all applications except 16 inside and 50 outside.  The equivalent Sargent cam is the 13-0660. Use the B520-736 for modular cylinder lengths of 1 1/8",...
1 1/8" mortise cylinders fit the 650 series keyswitch.  The 650 series keyswitch when ordered with the cylinder, will come complete with the correct cylinder, cam, and any required blocki...
If blocking rings (PN 36-079) are needed, specify dimensions when ordering. See below for blocking ring (PN 36-079) dimensions.  Blocking Ring  Specify Dimension  1//8" ...
Typically for a 1-3/4" door you would use a 1-1/4" cylinder.  Use the Table in the Pricebook for a reference:  
A modular cylinder's length is determined by 4 basic parts; a cam screw, cam, plug extension, and a back housing.  Most of these parts are used in more than one cylinder length and...
Chexit devices shipped after 8-24-2015 with motor driven: The Chexit device will use a 1 1/4" mortise cylinder with straight cam. Schlage cylinder 20-001-114 recommended. CAUTION: The length of t...
Chexit devices shipped prior to 8-24-2015:The CX device will need a 1 1/4" mortise cylinder with a straight cam per page 2 of the installation instructions. A 996L-M for a 1 3/4...
A 1 1/4" mortise cylinder with straight cam (similar to the Schlage B502-191) or a 1 1/2" mortise cylinder with straight cam using supplied spacer collar. Cylinder length does not chan...
The Schlage rim cylinder lengths are given below and were measured from the face of the cylinder to the back of the tailpiece.  Because of allowable tolerances for each part the average length is l...
 The tailpiece of the rim cylinder can be inserted into the Von Duprin 98/99 rim device either vertical or horizontal.
Order the device as 88 NL less trim. The cylinder will be mounted to the face of the door. Use templates 10156 and 40015.
The 2670 Guard X uses a standard rim cylinder for either push side or pull side.  The rim cylinder can be installed to the outside of the opening with an offset pull to operate the 2670 Guard X d...
The 98/99 rim device can be converted to double cylinder 98-2 or 99-2. Double cylinder features an inside key cylinder which locks or unlocks the outside trim (Classroom Function) and an outside c...
The B220-001 is an FSIC rim tailpiece and driver.
A 1-1/8 through 1-1/2" mortise cylinder with straight cam per Step 4 of 512NL Instructions.
Rim cylinder housing only for FSIC is part number 20-079.
Rim cylinder housing only for SFIC is part number 80-129.
The Schlage small format interchangeable core rim cylinders 80-329, 80-159, 80-116, and 08-129 can accept 6 pin and 7 pin small format cores.
The Schlage SFIC rim cylinder driver is part number B520-365, shown below.     Figure 1: SFIC Rim Cylinder Housing
To add a cylinder to the 98/99-EO rim device order a 110NL-MD for metal door or 110NL-WD for wood door with a standard rim cylinder and prep the door per template.
The rim cylinder with thumbturn, XB11-979 (Figure 1) was designed to be installed on the inside head of the Von Duprin 98/99–2 double cylinder exit devices, see Figure 1. The rim cylinder with...
Standard Schlage rim cylinders will fit a total thickness of door and projecting trim of 3 inches, this includes a minimum of 3/8" of engagement of the tailpiece into the exit device.  See ima...
For total thickness measurements larger than 3 inches see the special cylinder offerings in Pricebook.  Specify the part number and include the total thickness.  We do not offer the ...
The 98/99 rim device can be converted to double cylinder 98-2 or 99-2. Double cylinder features an inside key cylinder which locks or unlocks the outside trim (Classroom Function) and an outside...
B502-899 is the tailpiece for both the SFIC and standard rim cylinders.
See descriptions for the 09-992 thru 09-997 parts kits for modular mortise cylinders.  The 09-998 is a kit for a rim cylinder.