Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ pull side closer with overhead stop and holder ”

Resolution: Special template ST-2211 is used to mount a 2030 series closer with a GJ 70,79,81,90, and 450 series overhead stops. This ST works with any GJ "surface" mounted stop. The 2030 closer cannot b...:

What special template (ST) is used with a 4110 closer and GJ90 series?

Resolution: ST-2730 is used with a 4110EDA closer and GJ901-904 overhead stop.This can only be used with GJ901-904.If a drop plate is required, a 4010-18 drop plate would be used (A 4110-18 drop plate can not ...:

Where is the RA closer reinforcement located on a frame for a Regular Arm Closer?

Resolution: Optional closer reinforcements are located at 3" from hinge jamb to the beginning of the reinforcement plate. This applies to Regular Arm, Parallel Arm, Top Jamb. Regular Arm (RA) closer reinfor...:

Can a pull side mounted 1460 open 180°

Resolution: A 1260 Pull Side can be mounted standard template for 180°, frame and trim permitting.:

What is a 62A shoe used for?

Resolution: The 62A shoe is used when it is necessary to install the door closer (lower) down on the door so that it will operate under accessories such as overhead stops, coordinators, etc.:

What are Hold Open Closers & Magnets?

Resolution: Hold Open Closers & Magnets (Fire/Life safety products) provide a wide range of solutions. Single or multi-point hold open closers Utilize an electromechanical closer. Hold the door o...:

Can I use a Glynn Johnson 410 with a 4040 regular (pull side) mount?

Resolution: ST-1630 is required when mounting a 4041 or 4040XP door closer regular (pull/hinge) side with a concealed GJ100 or GJ410 series over head stop.This ST also REQUIRES the use of a 4040-18TJ drop plat...:

Can a 4040 regular mount installed on the pull side and a Glynn Johnson 90 be mounted together?

Resolution: The LCN 4041/4040XP and the Glynn Johnson 90 series can be mounted in conjunction with each other without a special template. The 4040 door closer is on the pull side of the door and the GJ 90 is ...:

What is the difference between an LCN CUSH arm, and an LCN EDA arm?

Resolution: EDA ARM - The EDA arm is a heavy duty parallel arm mount. The degree of door opening is determined by the template used for mounting. EDA arm closers can only be mounted as a Push S...:

Can a 4040XP Pull Side closer be mounted with Swing Clear Hinges?

Resolution: ST-1583 is used to template a 4040XP closer mounted hinge side with swing clear hinges. This ST is templating only – it uses standard parts.For current ST add on pricing and temp...:

What special template (ST) is used with a 4040(XP) Rw/PA mount closer and a GJ overhead stop?

Resolution: The use of a 62A Shoe (required) would be used to mount a 4040XP Parallel Arm with a "SURFACE" GJ 70, 79, 81, 90, or 450 series stop. You would order the 4040XP with a Reg w/62A arm op...:

Can a Glynn Johnson 90 stop be used with a top jamb mounted 4040?

Resolution: A 4040XP-18G drop plate will be needed to drop the closer and arm down far enough not to conflict with the GJ 90 series overhead stop.:

Can I mount an LCN Cush closer with an GJ overhead stop?

Resolution: It would be unnecessary to use the CNS/Cush arm and the Glynn Johnson overhead devices in the same application, both mechanisms stop the door.:

Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ pull side closer with overhead stop and holder ”

RELATED FAQS