PIM wake on radio

RELATED FAQS

Question
Answer
23848385 is the part number to order for the COM400 radio board that has the MCX jack for the optional RF antenna. It is shipped in the PIM400 and WRI400 so if needed for the wall mounted module yo...
The only difference between the COM400 in a door lock (AD400) and the COM400 in a wall mounted interface module is the MCX jack, which is provided for the optional remote RF antenna when needed o...
The COM400 has only two versions of FW, 2.2a and 2,2d and they are cross compatible and completely functional with all AD-Series wireless devices. There is no reason to change a FW 2.2a to a FW 2...
With the SUS connected to the AD400, in the EDIT tab there are radio communication settings "FIRST/DELAY/RETRY." FIRST - Is the first delay after the initial transmission of credential data, befor...
AD400 factory default settings when shipped are FIRST = 300 (m sec), DELAY = 200 (m sec) and RETRY = 5  
To change FIRST/DELAY/RETRY connect and couple the SUS/HHD to the AD400 and find under the EDIT tab the FIRST/DELAY/RETRY settings. See notes Or connect the SUS/HHD t...
PIM400-485 and AD400 Two red SCHLAGE LED flashes indicates the AD400, PIM400-485 and ACP all have operational communication, and the ACP denied access with a RS-485 command. With a PIM400-485 tw...
PIM400-TD2 and AD400 Two red flashes indicates the AD400, PIM400-TD2 has radio RF communication; but the AD400 did not get a strike, GO, relay closure from the ACP. With a PIM400-TD2 TWO red fla...
  ONE red flash, One red flash indicates RF COM loss, the AD400 radio did not get an answer from the PIM400-485 radio or the PIM400-TD2 radio. The PIM400-485 will turn off it's radio if th...
RF, wireless activation
Causes for AA battery drain in AD-Series LOCKS Possible Cause Fix/Corrective Action 1)      One the four (or eight) AA was inserted reversed and the rese...
Dynamic Channel Switching is a feature of the Schlage AD-series wireless access point modules. Dynamic Channel Switching (DCS) increases the robustness of the wireless RF communication in a noisy r...
  Here is a Technical Note on what Dynamic Channel Switching is, what it improves, how to set-up, and frequently asked DCS questions. DCS Tech Note here  
Setting Dynamic Channel Switching   1)     Connect and couple the SUS to the PIM400 you intend to change. See the SUS User Guide for details   2)     Under “PIM Properties” and the “Edit” tab is ...
Radio Frequency
The measure of the number of radio wave cycles completed in a period of time
Amplitude Shift Keying or modulation – Refers to the process of altering the height of the radio waves to signify the zeros and ones in the binary communication – ASK is the most common form of mod...
Is a wireless technology standard for exchanging data over short distances (using short-wavelength UHF radio waves from 2.4 to 2.485 GHz) from fixed and mobile devices
Indicates the span of radio wavelengths from 902 MHz to 928 MHz (megahertz). The AD-400 Series uses 900 MHz for wireless communications.
A radio device that retransmits received signals for the purpose of extending transmission distance or overcoming obstacles.
It is the responsibility of the installing contractor to install all material in accordance with SDI or HMMA installation standards and tolerances. Out of square frames which are installed out of t...
This condition (toed in or toed out jambs) is usually not found until the door is installed. Frames which have toed in or toed out jambs have been installed out of tolerance. It is the resp...
Drywall Slip-on frames are recommended and designed to be installed as KD (Knock Down) assemblies and not recommended to be welded (SUA). If a DW-Series or K-Series is welded prior to installa...
Used to describe how far radio waves can travel with no obstructions.
Smart cards can come in two forms: contact and contactless. Contact smart cards operate much like magnetic stripe cards (credit cards, etc.), requiring insertion into or direct contact with a rea...
Use a multi-meter in series with the batteries to measure battery current.  Be sure your multi-meter can accurately measure very low current, in the micro-amp range. See the attached Technical Not...
The changing of radio waves in a specific manner in order to represent data
Z-Wave® is a mesh networking technology developed in 1999 to create a standard for wireless radio frequency (RF) communication for home devices. The key to the technology is that Z-Wave products ...
Frequency Shift Keying or modulation – the process of altering the frequency of radio waves to signify the zeros and ones in the binary communication.