Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
mortise NL screw
”
RELATED FAQS
Question
Answer
What is the part number for the 99 series NL drive screw?
Resolution:
The part number for 98/99 series NL Drive Screw is 970441-89. The NL Drive Screw is also available in package of ten, part number 090074-00 NL Drive Screw can't be substitute with a standard sc...:
Why does my 7500 retract the latch bolt but not re-lock the trim?
Resolution:
Tips for changing the function: The NL Drive screw will not be visible when lock body is set to Classroom function There is locktite on the screw that makes it seem like its turned down enou...:
Does the Von Duprin E996L trim require the NL drive screw be installed into the device to function properly?
Resolution:
Von Duprin 98/99 NL drive screw is located in back of the 98/99 center case assembly. NL drive screw should be left in with trim lock slide plate in up position in the 98/99 exit device with E99...:
What cylinder does the 512 TP NL use?
Resolution:
A 1-1/8 through 1-1/2" mortise cylinder with straight cam per Step 4 of 512NL Instructions.:
How can the Von Duprin 98/9975-L with 996L classroom trim function be converted as a night latch function in field?
Resolution:
The following steps are required to convert the Von Duprin 98/9975L from classroom to night latch function: Order new 996L-NL-M trim and reset NL drive screw in mortise lockbody as se...:
What cylinder is used for the Falcon 510L and 510L-NL trim?
Resolution:
The Falcon Monarch 510L and 510L-NL trim will accept either a 1 1/4" Mortise cylinder with a straight cam or a 1 3/8" Mortise cylinder with a straight cam using the blocking ring provided with the ...:
How do I change the function of the Von Duprin 7500 mortise lock from Lever ( classroom ) to NL ( night latch )?
Resolution:
To convert the Von Duprin 9975L to 9975NL exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory): Turn the NL screw on 7500 mortise lock counter clo...:
Does Von Duprin supply the 9875, 9975, 9875-F and 9975-F mortise exit devices with NL-OP trim function?
Resolution:
For night latch function with pull by others, the 98/99 series mortise exit device should be ordered as NL less trim, e.g., 9875NL-L/TRIM. We will furnish a device only, and the mortise cyl...:
How do you change the Von Duprin 990TP trim to NL function?
Resolution:
Recommend to order a new 990NL-R/V or M trim to change from TP/Classroom function to NL/Storeroom function. You will also need to reinstall the NL drive screw back into into the mast...:
What is in a 23538820 Tamper Torx Screw Pack for AD-Series Mortise Locks?
Resolution:
(2) SCREW, TORX, T-15, #8-32 UNC 2A, UNDERCUT, FLAT HD, MACHINE, 1/4" LENGTH (2) SCREW, TORX, T-20, #12-24 UNC 2A, UNDERCUT, FLAT HD, MACHINE, 1/2" LENGTH (2) SCREW, 8-32 X 3/4 MS PIN TORX (1)...:
What other locks can the blue lever removal tool 24002693 be used with?
Resolution:
On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project. This tool can be used for Schlage ND-Series ...:
Are parts still available for the old Falcon M locks?
Resolution:
Related solution: What is the part number for the lever return spring for the old M series mortise lock?:
Why doesn't full rotation of the AD or CO Series Exit Trim (993) outside lever fully retract the Von Duprin 98/99 Exit Device latch?
Resolution:
- AD Series and CO series products require that the Night Latch (NL) screw is installed in the exit device. Be sure this screw is installed- Exit hardware and strike must be properly mounted ...: