mortise lock body parts

RELATED FAQS

Question
Answer
The only parts that are available for 34/58 for mortise lock bodies are: 091032 Aux Bolt Spring Pack of 10 091031 Dog Spring Pack of 10 091030 Thumb Spring Pack of 5
See Step 3 of the mortise lock reversing instructions(D-4010) which shows function conversions and what part(s) are needed if any are needed.
The Von Duprin 7500 mortise lock body ships in the NL mode.  Either the function of 7500 lock body has not been changed to the Classroom function or the NL Drive screw is not all the way down. Step...
  Tips for changing the function: The NL Drive screw will not be visible when lock body is set to Classroom function There is locktite on the screw that makes it seem like its turned down enou...
The Von Duprin 7500 mortise lock body will replace the old style 34 and 58 lock bodies. Order a 7500 mortise lock in the proper finish. The old style strike must be replaced with 575 strike becau...
You can reference the 7500 mortise lock rehanding instructions. Remove the two screws from mortise lock faceplate. Remove the face plate and the collar from the mortise lock then rotate the la...
The following steps are required to convert the Von Duprin 98/9975L from classroom to night latch function: Order new 996L-NL-M trim and reset NL drive screw in mortise lockbody as set from...
The springcage part number is L283-040.
The part number is the 09-402, specify the design and finish.
Inside knob and bushing: 09-402 plus design and finishOutside knob: 09-401 plus design and finish
See table below for part numbers. Table 1: 09-900 part number variations
Schlage does offer rabbetted latch and strike kit: Part number, 39-030, for cylindrical locks and deadbolts.  Part number, 10-075, for the L9000 mortise locks. Monarch does not offer rabbette...
Falcon is reintroducing the lever return spring for the discontinued Falcon M mortise series.  Effective November 1, 2014 the lever return spring is now available for purchase with a list pric...
Only the lever return spring is available.
Related solution: What is the part number for the lever return spring for the old M series mortise lock?
The Schlage L-Series mortise lock spindle and spring part number can be found in the Table 1.     Spindles and Springs   Part Number  Description  L283-060 Spindle and spring, 1...
Outside Knob/Lever and Rose/Escutcheon Assemblies      Part Number  Description    A Rose with Knob/Lever  09-506  Designs: 01 02 03 05 06 07 12 17 18 OME 41 42     09-655  Des...
Schlage does not have a stainless steel/non-ferrous lock series. The only option that Allegion provides is the Grade 1 cylindrical Falcon X-Series. To order the Falcon X with the stainless st...
The L9453 mortise lock case part number is L283-137.
At one time we offered a 9453 function in several different lever, knob and grip handleset designs. A wide variety of trim offerings were available. The mortise lockcase was a smaller version of th...
Doors that may be slightly under 1 3/4" thick may experience binding.  To resolve simply remove the spindle springs and discard.  Alternative solution is to install the OSU ferrule kit (L583-347)....
While they are both mortise locks they are not interchangeable.  You would NOT be able to use a L9000 with a VD panic device. You would NOT be able to use a VD 7500 with Schlage lev...
The replacement solenoid for the Schlage L-Series mortise lock is part number L283-053.
See Falcon MA lever assembly below: The spring mechanism (E) returns the lever to horizontal.  The parts are not sold separate, so if the lever sags, the entire lever assembly shoul...
Lever assemblies part numbers are found in the Pricebook.  Note they are handed.
The Schlage L-Series uses a clover leaf cam with the exception of the L9060 outside cylinder which uses a straight cam. The cam part number will depend on the type of mortise cylinder, keyway (for ...
Schlage offers a comparable cam to the Yale 2160 and it will operate any Yale lock that utilizes the Yale 2160 cam.     Schlage Cams for Yale 2160  Part Number  Description  B520-7...