Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ LCN Benchmark power requirements ”

Resolution: Von Duprin PS914 x 900-4RL supports two EL with two auto operator.:

What power supply do I need for my 2 QELA devices with LCN auto operator?

Resolution: Use the PS902-2RS power supply with LCN auto operator on single door, PS904-2RS power supply on double door and PS904/906-2RS-2RS for 2 pair of QELA is required for basic operation with a...:

What is power boost on a Senior Swing or Benchmark operator?

Resolution: Power Boost is a positive latching feature that increases the latch force, to over come building stack pressure or door weather stripping, etc, if the door stops before co...:

Will the 9100 series Benchmark III power an electric strike?

Resolution: The Benchmark III control has a 24VDC, 2.5 amp power supply, and built in relay for controlling electric strikes or other accessories less than 2.5 amps current load. For a fail secure strike, r...:

Are there parts available for the obsolete 330 series door closer?

Resolution: The 330 closer and parts were discontinued in early 2009. LCN does not have any parts available for the 330 series closer. The LCN 3030 Series would be the comparable closer replacement to the...:

How do I program my device?

Resolution: The programming processes for Allegion devices can be both product and features specific. Some products programming processes are electronic in nature, others are physical in nature. &nb...:

Do LCN closers come with thru bolts?

Resolution: The standard screw pack for an LCN closer is the SRT (Self Reaming and Tapping) screw. Thru bolts are an option, but must be specified on the order. There is no charge for them, but they do need to...:

How do you change a 9130 Benchmark to a 9140 Benchmark?

Resolution: The only difference between the 9130 and 9140 Benchmark operators are the arms.To convert a Benchmark 9130 (pull) to a 9140 (push), order a 9140-3077 push arm assembly for revea...:

How do I fix a Benchmark 9100 that the belt keeps sliding down on motor gearbox?

Resolution: The Benchmark and Falcon operator gearbox assemblies are not repairable. The gearbox belt and/or pulley cannot be replaced in the field, the gearbox would need to be replaced as a complete assembly...:

When did they start putting the green dial's on the 4041 closers?

Resolution: LCN started putting on the green dials for the spring adjustment on the 4041's in 2001.:

How do I get service on my Astro Swing operator that isn't working properly?

Resolution: LCN does not does not have or supply any information for the old (obsolete) "High Energy" Dor-O-Matic Sliding doors, Bi-Fold doors or Astro Swing doors. You MUST be AAADM certified to work on, or g...:

What actuators can be used on the 8310-866 Bollard post?

Resolution: The LCN Bollard post (8310-866) only accepts the "square" actuators (no round actuators). The size of the Bollard post is 4” X 6” X 36”. Acceptable actuator part numbers are: Hard Wired - 831...:

What maintenance is required for an LCN closer?

Resolution: Closers mounted according to LCN installation instructions require no periodic maintenance or seasonal adjustments. Monthly, quarterly, and annual visual inspections are recommended for Fire/...:

What side of the door is the 4040SE mounted?

Resolution: The 4040SE is non handed and can be mounted on the push or pull side of the door.Installation Instructions :

What are the power requirements for the 8310-865 (433 MHz) receiver?

Resolution: The input voltage for the 8310-865 (433 MHz) receiver is 12-24 VAC/VDC +/-10%, the current draw is 250mA (0.25A).:

What gauge wire is needed for CX red and black power wires?

Resolution: For Product Shipped prior to 8-24-2015 with solenoid and EPT or Door Loops: a. 0-100 ft, use #14 Gauge Wire ...:

What are the power requirements of the 4600 series operator?

Resolution: The 4600 series operator requires a 120 VAC @ 1.5 Amp power input to be field connected. Hardwiring is always recommended, but a "plug-in" line cord can be installed (by others) with the proper cor...:

What is the power requirements for the CT5000 / WRI400?

Resolution: 12.0VDC or 24VDC with current rating of at least 0.5 amp (500ma).:

What special template (ST) is used with a 4040(XP) Rw/PA mount closer and a GJ overhead stop?

Resolution: The use of a 62A Shoe (required) would be used to mount a 4040XP Parallel Arm with a "SURFACE" GJ 70, 79, 81, 90, or 450 series stop. You would order the 4040XP with a Reg w/62A arm op...:

Can you operate a Doromatic EL 1490 with an LCN power supply?

Resolution: This is not possible. Due to the device's 16 Amp in-rush it would require it's own PS914-2RS which will power 1 or 2 devices.:

Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ LCN Benchmark power requirements ”

RELATED FAQS