IC core tailpiece

RELATED FAQS

Question
Answer
The B series accepts 6 or 7 pin small format cores when specifying with the "BD" cylinder suffix (less small format interchangeable core).  The tailpiece shown below is used for both...
The Schlage ND is shipped with a driver/tailpiece when ordered with a LD, BD, or JD suffix.
The T lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied (including the tailpiece) Example: T581J IC-SC
Yes. Both Schlage and Falcon SFIC mortise housings will accept 6 and 7 pin cores with no additional parts.
There are several ways to spot differences, see Figure 1, but the easiest is to look at the face of each core. The face of both cores looks like a "figure 8".  With small format, bo...
For ND locks shipping on or after January 30, 2017, the lever and core driver will need to be changed to convert from JD to BD.SFIC lever, 03-200SFIC driver and spacer, 09-774
For ND Locks shipping prior to January 30, 2017:The springcage(s), lever, and core driver will need to be changed.  Depending on the function the components below are required.Outside spring c...
Image-1 below shows an exploded view of a Full Size IC core with the bottom pin circled in red.  This pin controls the lug that locks the core into place when inserted into a lever or hou...
The ND85/AL85/A85 hotel lock is only available in a conventional Key-in-Lever cylinder.  Interchangeable core and Primus are not available with this function. 
A Primus Hotel cylinder (as well as an IC hotel cylinder) is not possible because there isn't enough room inside the cylinder for all of the required components. 
The "C" indicates small format IC core, which is the only core style Falcon products.  The C987 will be provided less core unless -6, or -7 suffix is specified (6 or 7 pin core) Example:...
This is usually caused because the wrong tailpiece is being used on non-IC cylinders or the incorrect driver for IC options. Use the below descriptions to identify which they need.NON-IC: There are...
The Monarch KIL trim uses the following cylinders: Schlage Cylinders 23-013 Conventional 20-750 Primus 20-750-XP Primus XP 20-550 Primus UL437 20-550-XP Primus UL437 XP Falcon Cylinder A23165-0...
The Schlage Full Size IC core is 6 pin only. 
The RU lock can accept a Schlage Full Size core, but the cylinder suffix must be specified as "J IC-SC" so the correct parts are supplied. The tailpiece will come with the lock. Example: RU581J IC-SC
There are different mortise cylinder length options depending on the cylinder type. Below is a list of available options for conventional, FSIC, and SFIC cylinders, as well as the convent...
Specify the J cylinder suffix followed by IC-CR6 or IC-CR7 (6 or 7 pin Corbin core) Example: T581J IC-CR6  This will accommodate an 8000 or 8000-7 Corbin Russwin Full Size core.
Conversion kits are available to convert many popular functions.Conversion kits manufactured on or after January 30, 2017 will have the new enhanced ND spring cage, lever, plunger and buttonCo...
For all available ND Series Conversion Kit part numbers, click here.
It is not possible to key SFIC and standard cylinders including Schlage FSIC into the same system.  A keyway name may be shared between the two key fami...
The Schlage small format interchangeable core rim cylinders 80-329, 80-159, 80-116, and 08-129 can accept 6 pin and 7 pin small format cores.
The 914KIL-IC trim is shipped with a Small format interchangeable core (SFIC) in a 6 pin "A" section/keyway.  A comparable core from Falcon would be the C646 (uncombinated - no pins) or C...
Refer to Table 1 for a list of T lock tailpieces for conventional cylinders.  Table 2 shows IC tailpieces. Table 1: T lock conventional tailpieces Table 2: T lock IC tailpieces