Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ HHD programming with legacy ”

RELATED FAQS

Resolution: Cable used to connect Hand Held Device (HHD) to CIP for programming legacy CM/CL/KC products:

Can I have multiple Hand Held Devices (HHD) coupled to the same lock?

Resolution: The Coupling Password is compared whenever an HHD is trying to adjust lock configuration settings or downloading door programming files.:

Will a new RF "programmable" transmitter work with an older RF receiver that has "dip switches"?

Resolution: The newer "programmable" RF transmitters/receivers will not work with the older "dip switch" transmitters/receivers. The frequency and coding are different.:

How do I clear the memory on a CT500?

Resolution: To clear the memory on a CT500 controller, deleting all programming and codes from the controller and resetting to factory defaults, perform the following procedure: 1. ...:

Replacement BNC Cable for SNAP Programmer

Resolution: This product is obsolete and is no longer available from Schlage Electronics.:

Why does my AD-200 not accept a new programming code?

Resolution: Early versions (12/09 ) of the AD200 User Guide in many DEMO kits incorrectly state the Programming sequence to change the a programming code. It shows entering the new programming code o...:

How do you program the 8310-865 RF receiver?

Resolution: To program the 8310-865 receiver: Set the dip switches 1 to the "OFF" (pulse) position. Set the dip switches 2 to the "OFF" (0.5s) position. Momentarily press the " No Delay" or "Delay" ...:

How do I program Locknetics CM / CL legacy locks with the Schlage Utility Software (SUS) and Hand Held Device (HHD)?

Resolution: - With the CIP NOT inserted and the Schlage Utility Software (SUS) running o Enter the Master Programming PIN or Present Loc...:

CIP

Resolution: CIP Module (P512-112) used with HH-Serial Cable and Hand Held Device (HHD) for programming legacy CM/CL/KC products. Used only with BM-150 HHD:

HH-2PIN Serial

Resolution: Cable used to connect Hand Held Device (HHD) for programming legacy CM/CL/KC products. Must have SUS 6.3.3 in HHD to support the HH-2PIN Serial cable.:

PIM COMPATIBILITY

Resolution: No, the AD400 / WRI400/ WPR400 only work with the PIM 400-485 or PIM 400-TD2. The legacy WA locks / WRI / WPR2/ WSM only communicate with the legacy PIM-485 or PIM-TD2.:

What versions of Microsoft Windows are compatible with Schlage Express version 4.4.2?

Resolution: Microsoft Windows 8, 7, Vista, and XP: Home, Basic, and Starter versions are not compatible with Schlage Express. What versions of Microsoft Windows are compatible with Schlage Express v...:

Can the low coin cell Nuisance delay be Disabled on a CO200?

Resolution: The coin cell is ignored when the lock sets are used with Manual Programming ONLY or while in Construction mode.:

I have an old PL series padlock what is the KS replacement?

Resolution: :

CT5000 USB Cable and Single gang plate part numbers and purpose.

Resolution: The 15” cable is intended to allow the CT5000 to be installed near the door opening and bring the HHD USB programming port down to a reasonably accessible location for access programming and s...:

Why doesn't my AD lock go into Construction Mode?

Resolution: Update your device firmware to the latest version to fix this early design / feature update:

Can the AD-200 and CO-200 be manually programmed?

Resolution: Yes. The AD-200 and CO-200 each can be managed through manual direct lock keypad programming or PC software programming using an HHD to transfer programming information to the lock....:

Why do I get error message "E701 - Programming Lock Failed" on my Hand Held Device while programming an AD lockset?

Resolution: Update your lockset using ADFwPkg 2.19.0 or higher. This new firmware update resolves this programming error problem (E701) and the error will no longer be presented.:

Where is the cross reference list for PS800 to PS900 series power supplies?

Resolution: Von Duprin PS914-4RL power supply replaces the PS873-4TD.:

Do all Senior Swing operators come with the Push-N-Go feature?

Resolution: All Senior Swing models are heavy duty operators and have the Push-N-Go (PNG) feature. This feature is a programmable function in the control module. The PNG settings are:&nb...:

Can the new 900-2Q option board be used with an old Von Duprin PS873 power supply?

Resolution: The PS900 power supplies will only accept the 900-XX option boards.:

What are the model numbers for the new Schlage and XceedID wall mounted credential readers?

Resolution: The Legacy wall mounted readers are replaced as shown in the table below: The MTMS15 and MTMSK15 did not have any prior models that it replaced.:

Can the AD-Series and CO-Series magnetic card credential readers be set to read data from different magnetic card tracks?

Resolution: Customers will need to use the Schlage Utility Software (SUS) on the HHD lock programming device to set the desired magnetic track to be read for access control, if not using default Track 2&n...:

How do I manually change PIN length on an AD200?

Resolution: Beginning with Firmware Packages ADFwPkg 2.16.3 and COFwPkg 1.20.0 the PIN length can be manually changed for AD200 and CO200 locks as follows: 1. Press {programming code (default is 97531)} then ...:

CT5000 Construction Mode

Resolution: Creating a Master Construction Credential - From first power up or after clearing memory: Remove the CT5000 lid. Press and hold the Schlage button. Present a credential to the reader within ...:

How do I manually program the AD300 RS-485 Address?

Resolution: Manually Setting the RS-485 Address This method is only available before the first network communication between an Access Control Panel (ACP) and the lock. Do a Level 1 and Level 2 Factory De...:

How many door files should the Hand Held Device (HHD) be able to store at one time?

Resolution: For best Schlage Utility Software (SUS) and Hand Held Device (HHD) performance do not put more than 100 door files at a time ....:

PIMWA-CV

Resolution: Null converter used to connect Hand Held Device (HHD) to WA Series Legacy PIM, using the HH-Serial Cable:

CM Lock Manual Programming Disabled

Resolution: When trying to program a CM lock, it may display an error code with a solid green light and 10 read flashes. This indicates the lock has already been programmed with computer software and manual ...:

How do I program my device?

Resolution: The programming processes for Allegion devices can be both product and features specific. Some products programming processes are electronic in nature, others are physical in nature. &nb...: