Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
edge guard price
”
RELATED FAQS
Question
Answer
What is the difference between the Ives 482B and the 482A door guards?
Resolution:
The difference between the Brass version 482B and the Aluminum version 482A is the size and design as well as the base material and available accessories. The Brass version 482B comes w...:
Where is the catalog information and specifications on the Ives edge guards?
Resolution:
Information for Ives edge guards can be found on pages B51-B53 of the Ives Catalog linked here, and in the edge guard ordering guide linked here.:
Does the Ives 482 Door Guard come with a rub plate?
Resolution:
The Ives 482 does not come with a rub plate. The brass 482 Door guard (also called 482B) comes with an edge guard or plate that is applied with adhesive to protect the edge of the door.T...:
Is there an electric strike that will work with the 2670 Guard X?
Resolution:
The Von Duprin 2670 Guard X does not have a spring loaded latch bolt, it is a dead bolt and will not operate with any electric strikes.:
How long is the RGO?
Resolution:
The RGO (rod guard only) is 36" long x 1-5/8" wide.:
Can the 2670 be cut down to fit smaller door widths?
Resolution:
The 2670 Guard X device can't be cut down to fit doors less than 3 feet. This device is designed to fit doors 36"- 48" in door width.:
What exit device is weather rated?
Resolution:
Exit devices are not designed for exterior application. If used in an exterior applications then a powder coated finish on the 33/35 and 98/99 series are recommended for exterior applications. ...:
What is the part number for the pcb board on the 2670 Guard X exit device?
Resolution:
The following are part numbers for 2670 Guard X exit device PCB: pcb.10018 for English pcb.10019 for Spanish pcb.10020 for French:
Does Von Duprin offer any pulls that through bolt to the Guard-X device?
Resolution:
Von Duprin does not offer any lever trim or pulls that through bolt to the Guard X device. Ives has the 8102-6 and 8105-6 pulls that can be lined up with the mounting screws of the exit device b...:
LATCH GUARD
Resolution:
RG-27 (LG):
EXTENDED LATCH GUARD
Resolution:
LGO, LGO-3, LGO-4:
ROD GUARD
Resolution:
RGO, RG-27, RG-27-3 , RG-27-4:
PLASTER GUARD
Resolution:
Dust Cover Box, Masonry guard, Mortar Guard, Plaster Guard.; Grout Guard:
After replacing the battery on a Von Duprin 2670 Guard X why would the horn stop working?
Resolution:
Replacing the battery on the 2670 should not cause the unit stop working. Make sure the spring that provides tension on the plastic finger is not bent out. The spring should be at a 90 degrees...:
Is the Von Duprin Guard-X exit device fire rated?
Resolution:
The Von Duprin Guard-X exit device is not fire rated because the deadbolt is not spring loaded. Therefore, there would be no positive latching as required on a fire rated opening. :
Is the 2670 Guard X fire rated?
Resolution:
The Von Duprin 2670 Guard X is used only on non fire rated doors thus is not fire rated.:
How to replace the circuit board or horn on a Guard-X device?
Resolution:
See PCB replacement instructions below. The horn is part of the board and can only be replaced by replacing the entire board.:
What strike is required when using the 2670 Guard-X on a pair of doors?
Resolution:
With a mullion: Use the standard strike 267 With no mullion and inactive leaf being held closed with flush or surface bolts: Use the 2609 double door strike :