Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ D series driver ”

RELATED FAQS

Resolution: The A700-009 driver was obsoleted August 2005 and was replaced with the A700-039 driver and A700-041 finished cap.:

The key just spins on a B560R B561R or B563R deadbolt.

Resolution: The Schlage full size interchangeable core (FSIC) prepped B560F, B561F, and B563F deadbolts all require a UL fire cup (R) in order to be UL listed. This fire cup is s...:

New FSIC driver info for the AL locks.

Resolution: The new AL FSIC driver part number is A700-052. This driver snaps onto the back of the core similar to the ND, as opposed to it being assembled into the lock chassis with a retaining ring. Th...:

Why can't a new spring cage or driver be installed on an older AL lock?

Resolution: In 2002 the Schlage AL-Series underwent a design change that affected the spring cage, driver, and plastic insert. Spring cage and driver replacements for AL locks manufactured before this design ...:

What is the part number for the 99 series NL drive screw?

Resolution: The part number for 98/99 series NL Drive Screw is 970441-89. The NL Drive Screw is also available in package of ten, part number 090074-00 NL Drive Screw can't be substitute with a standard sc...:

What are the part numbers for the SFIC driver and spacer used on the ND series locks?

Resolution: There are several part numbers available: Part Number Contents 09-774 SFIC driver & Spacer N523-091 SFIC driver D500-000 Spacer:

I am unable to remove my key from a B600 B700 B800 deadbolt.

Resolution: This is usually caused because the wrong tailpiece is being used on non-IC cylinders or the incorrect driver for IC options. Use the below descriptions to identify which they need.NON-IC: There are...:

What is the part number for the full size core driver for the ND series?

Resolution: The ND-Series FSIC driver is part number N523-127.:

Clip on the B500 or D200 SFIC deadbolt comes off shortly after installation.

Resolution: Verify the door thickness is 1 5/8" or greater per the pricebook. Thin doors will force the clip off the housing. If door thickness is correct then replace the product as needed. ...:

What is the tailpiece and driver part number for the 20-057?

Resolution: The B220-001 is an FSIC rim tailpiece and driver.:

Did the AL series SFIC lever inserts change?

Resolution: The SFIC lever insert part number prior to 2001 was the A700-022.:

Does the Von Duprin E996L trim require the NL drive screw be installed into the device to function properly?

Resolution: Von Duprin 98/99 NL drive screw is located in back of the 98/99 center case assembly. NL drive screw should be left in with trim lock slide plate in up position in the 98/99 exit device with E99...:

DRIVER

Resolution: Tailpiece:

How do you remove an AL lock from a door?

Resolution: AL-Series and discontinued D Lever-Series locks use castle nuts to hold the chassis to the spring cages and to keep the chassis positioned in the door. This causes confusion at times when the lock ...:

Schlage AL small format spacer installation requirements.

Resolution: The Schlage AL-Series SFIC locks require one (1) small format spacer (D500-000) for 7-pin cores and two (2) small format spacers for 6-pin cores. When these spacers are not ins...:

What is the part number for the SFIC tail piece for a W lock?

Resolution: Q330-168 SFIC Tailpiece (throw member for levers) Q330-169 SFIC Tailpiece (throw member for knobs) :

What is the part number for the SFIC driver on the AL locks?

Resolution: The small format core throw member for the AL locks is C604-381.:

How long is the ND tailpiece for a thick door?

Resolution: Schlage ND-Series tailpieces for extended doors are available by only two means, but are not available to order separately. If an extended tailpiece is needed, then a complete lock ...:

When ordering the ND lock less cylinder will it come with a tailpiece?

Resolution: The Schlage ND is shipped with a driver/tailpiece when ordered with a LD, BD, or JD suffix.:

What is the part number for the driver for a FSIC on an S lock?

Resolution: The part number is S605-242.:

What is the part number for the SFIC rim cylinder driver?

Resolution: The Schlage SFIC rim cylinder driver is part number B520-365, shown below. Figure 1: SFIC Rim Cylinder Housing:

Driver pins on SFIC mortise housings loosen up and fall out.

Resolution: Issue: Schlage SFIC mortise cylinders have potential for the driver pins to fall out affecting the ability to lock and unlock the device.Facts: Housings manufactured between 06/01/2...: