can anti ligature trim be installed on existing locks with escutcheon trim

RELATED FAQS

Question
Answer
The standard L9000 lock can be ordered for thin doors (1 3/8") and the appropriate parts will be shipped.  The LV9000, L400, LM9000, Anti-Ligature, and N escutcheon trims a...
Schlage offers a High, Medium, and Low risk HSLR ligature Resistant trim offering for the L9000 and ND locks, Data Sheet.Schlage offers a Low to Medium Risk SL1/SK1 ligature resistant trim for...
High Risk Areas*Patient bedroomIn-suite bathroomIn-suite closetTime-out roomPatient difficult to manage; or risk of solitary and/or unsupervised areas.Medium risk areas*Living roomDining roomGroup ...
See image, ANSI A115.1 Mortise Lock PrepThis door prep requires the N escutcheon with the L283-029 spacer kit to keep the springcage from falling into the door.  Spacer kits are...
Typically for a 1-3/4" door you would use a 1-1/4" cylinder.  Use the Table in the Pricebook for a reference:  
The Schlage L0170 is not available with the L escutcheon design because due to the narrow size you cannot fit the mounting plate underneath.  The mounting plate must sit on a "diamon...
The SL1/SK1 was released in February 2011 for use on the L9000 mortise lock.
The 996EO trim is just the plate without the lever and cylinder hole
The L283-150 is a modified mounting plate to allow a user to only install trim on the inside of the L9000.  For installation and door prep requirements, see the install sheet.  Add...
Frascio is a company that provides decorative lever sets for many of Allegion products.  More information can be found on their web site at WWW.frasciointernational.com.
The following templates are for the MA lock.  Use the matrix in each template for the specific function.  See here for Sectional trim . See here for Escutcheon trim. 
Schlage has conversion kits to convert the classroom L/LV9070 to the classroom security L/LV9071 and the classroom holdback L/LV9076 to the classroom security holdback L/LV9077.  The...
The Danmark levers were available in rose trim only.
The Schlage L9000-Series with anti-ligature trim cannot be ordered less cylinder (L cylinder suffix), but can be ordered less core (BD or J cylinder suffix). The cylinder rose dimensions change bas...
1) Make sure the lock batteries are more than 4.0 volts. The USB connection will not detect or communicate with a voltage lower than 4 volts. Many times a firmware update will draw d...
2) Make sure the SUS/HHD is set to communicate using USB connection mode in SUS.  You should see the familiar USB symbol on the SUS main Screen in the bottom right corner.  If you see a S...
3) When you update with NEW firmware replacing very OLD firmware a S1 RESET is suggested after the update. This initializes all the AD-Series memory locations to the new firmware. S1 is the ...
4) Make sure the HHD-USB cable is securely inserted into the HHD and into the lockset.  
5) Inspect the HHD-USB connector(s), ensure no pins are damaged, recessed or out of alignment. If a damaged cable is found customers should see their dealer for a replacement or they can order a re...
5) If working with a CO lockset, the mechanical key switch needs to be in its "Inactive" or normal position.  Ensure the triangle alignment on the front escutcheon and that...
Torx screws are not standard on the SL1/SK1 trim but are available as an option. Specify the L283-121 Torx screw pack.  This pack includes torx screws for the armor and strike. 
We have several blank trims listed in the price book to cover existing trim prep in door.  DEVICE EO TRIM   22  230EO  88  880EO   98/99  990EO or 996EO*  33A/35A Rim, 33/3...
You can order an L lock with a lever on one side and knob on the other as long as it's still rose by rose, or escutcheon by escutcheon (must be same style escutcheon). EXCEPTIONS: Knob trim on the...
Includes the SL1 lever on one side and the SK1 knob trim on the other side.
No parts are compatible between the Falcon MA-Series and the obsolete Falcon M-Series.
The following steps are required to convert the Von Duprin 98/9975L from classroom to night latch function: Order new 996L-NL-M trim and reset NL drive screw in mortise lockbody as set from...
The L Series lock can fit into a door prepped for the SCHLAGE K Series with some additional prep as described here.  
K and L trim and parts are not interchangeable. 
The AD200, 250, 300, and 400 trims will work with the Von Duprin 98/9975 mortise Exit Devices.
  Schlage H-Series Escutcheons    Part Number  Description Dimension   07-057  Inside escutcheon and turn  6.92" x 2.75"  07-035  Inside escutcheon, dummy - H170  6.92" x 2...
Causes for AA battery drain in AD-Series LOCKS Possible Cause Fix/Corrective Action 1)      One the four (or eight) AA was inserted reversed and the rese...
The Falcon MA mortise lock is available with an occupancy indicator on the following functions: MA301, MA311, MA321, MA371, MA431, MA441(inside of door only), MA451, MA541, MA57...
Related solution: Is the MA indicator available separately? 
In late July, 2014, Schlage began taking orders for a new high visibility indicator for both N escutcheon and sectional trim applications.  A complete listing of lock functions and part number...
The L Series mortise indicator datasheet can be found here. Includes how to order.
Von Duprin 98/99 NL drive screw is located in back of the 98/99 center case assembly. NL drive screw should be left in with trim lock slide plate in up position in the 98/99 exit device with E99...
 Mounting Posts   Part Number  Door Thickness  L583-211  1 3/8"  L583-212  1 3/4" - See note section on SL1 trim  L583-213  2...
The 98/99 rim and vertical rod exit devices are shipped with NL drive screw to function as a Night Latch. To convert the device to Class Room, remove the NL Drive Screw on 98/99 center case ass...