Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
blade stop screw
”
RELATED FAQS
Question
Answer
What other locks can the blue lever removal tool 24002693 be used with?
Resolution:
On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project. This tool can be used for Schlage ND-Series ...:
Is the blue ND lever tool shipped with each lock?
Resolution:
The blue lever tool remover, 24002693, is not shipped in every box. The existing wire spring lever removal tool will be included in every box. :
What is the part number for a blade stop shim for a 6111 or 6113 electric strike?
Resolution:
010055-xx is the part number for Blade Stop Shim kit for 6111 or 6113 electric strike and it must be ordered separately. xx is for the finish callout.:
BLADE STOP SPACER
Resolution:
Shoe Spacer, Parallel Arm Closers, Aluminum Frame, Aluminum Store Front Frame:
What tool is needed for the NDE security screw?
Resolution:
You will need the T-15 and the T-20 Secure torx tool. You can order them from us. Part #: L283-121 Contains: (2) Armor screws, #8-32 x 1/4” (T-15) (2) Strik...:
Does the Allen head handing screw sit flush when fully installed?
Resolution:
The Allen head set screw will need to be threaded all the way to the head when installing. The head of the screw will be slightly below the case surface. &nb...:
BLADE STOP
Resolution:
Aluminum Frame, Aluminum Store Front Frame, Aluminum Door and Frame:
How is a bar coordinator installed on an aluminum frame with a 5/8" blade stop?
Resolution:
This can vary based upon situation. It may be able to either "cut away" the blade stop, or mount the COR with "spacer blocks" below the stop. Allegion does not sell spacer b...:
Hollow Metal price estimates
Resolution:
Pricing information is not a part of the Knowledge Center data. For all hollow metal price comparisons please e-mail the Steelcraft Estimating Team. For your reference, the e-mail address...:
How do you remove an AL lock from a door?
Resolution:
AL-Series and discontinued D Lever-Series locks use castle nuts to hold the chassis to the spring cages and to keep the chassis positioned in the door. This causes confusion at times when the lock ...:
Usable COM Port Range in CDT
Resolution:
:
What is the SUS feature "Device Template"
Resolution:
See the attached Technical Note for instructions on saving a "Device Template" FROM a device or loading TO a device, Device Template Tech NoteOn the SUS/HHD go to the LOCK Properties tab, and sele...:
Are parts still available for the old Falcon M locks?
Resolution:
Related solution: What is the part number for the lever return spring for the old M series mortise lock?:
Isonas RC03 with Intermittent Connection / Drop
Resolution:
If RC-03 Classics, set the port speed to 10mb / half-duplex, disable autonegotiate. If RC-03 Coldfire, set the port speed to 10mb / full-duplex, disable autonegotiate. Also. these devices...:
What comes with the 9530-MS Screw pack?
Resolution:
The 9530-MS screw pack is the Sr. Swing Pull Arm Screw bag and it includes; roller (1), MS (2), WS (2), Hex cap arm screw (1), washer (1), and rivet nuts (2).:
How do you mount a 55 rim with the 379 where the studs do not line up with the mounting screws?
Resolution:
Position the 379L trim and attach with countersunk screw into the bottom stud of the trim. Position the 55 Rim device and attach with the device mounting screw through the he...:
How do I prevent the arm screw from coming loose and sliding up and down the main arm?
Resolution:
If arm screw is not gripping the forearm tube enough to securely hold the rod and shoe in place: If the allen head on the arm screw (-83) is stripped out, try using a wrench to tighten it. Try ...:
What is the M504-413 tool used for?
Resolution:
See attachment that describes this tool.:
What tools and pinning kits are required to service Everest 29 keys and cylinders?
Resolution:
The current tools, pinning kits and key originating machines for all Schlage Everest full size cylinders and small format cores are the same used on Everest 29.:
Is there a tool to drill the thru bolt holes on cylindrical locks?
Resolution:
Order the M204-198 thru-bolt jig, see Figure 1. Figure 1: M204-198 thru bolt jig The 40-080 was the old Schlage jig. The 030736-000-70 was the old Falcon jig. When the jig changed to...: