Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ auxiliary bolt field replacement kit ”

Resolution: If the horn fail to operate in the CX device you need to replace the Chexit module. 040086 is the part number for devices shipped after 8-24-2015 with motor driven.050228 is the...:

Can you have Less Bottom Rod (LBR) on a 98/9947WDC?

Resolution: This option is available.If this is a fire-rated opening you must use the Auxiliary Fire Latch Kit to maintain your Fire Rating. If not fire-rated simply omit the bottom rod but be aware that...:

How do you convert the Von Duprin 370 series controls to NL or night latch function?

Resolution: You must have the Von Duprin NL Cylinder plate part number 967484-89 to convert the 370 series controls from classroom function to night latch function. If new installation, use the NL cylinde...:

Is there an EL conversion kit for the Falcon 2390 exit device?

Resolution: There is no EL conversion kit for a 2390, the device will need to be replaced.:

How can the Von Duprin 98/9975-L with 996L classroom trim function be converted as a night latch function in field?

Resolution: The following steps are required to convert the Von Duprin 98/9975L from classroom to night latch function: Order new 996L-NL-M trim and reset NL drive screw in mortise lockbody as se...:

Is there a Von Duprin conversion kit to change mechanical to electric latch retraction (QEL) in the field?

Resolution: Followings are the list of the electric latch retraction (QEL) kits:114317-00QELA Modular Conversion Kit040061-00QELA Modular Conversion Kit w/CON958002-00HD-QELA Modular Conversion Kit040062-...:

Is there a conversion kit to add Electronic Dogging (ED) or Electric Latch Retraction (EL) to a 1690 or 1790 in the field?

Resolution: There is no conversion kit to add EL or ED to an existing 1690 or 1790 series device. All of the components are built into the device, since the device does not have a separate base...:

What is the minimum dimension from the edge of the door to a glass light cutout?

Resolution: Minimum dimensions to cutouts for glass lights: Vertical edge of door to edge of cutout = 5 29/32" Top of door to top of cutout = 6" Bottom of door to bottom of cutout = 10" Reinforcing chann...:

Can the Von Duprin EL option be added to any existing 98/99 device?

Resolution: The Von Duprin EL option can be added to any existing 33A/35A, 98/99 series exit devices. :

Are window kits available for Steelcraft doors?

Resolution: Window kits are available for Steelcraft doors as either factory installed or prepared and installed by a distributor. Factory prepared light cutouts are supplied with Dezigner trim as ...:

What are the Von Duprin part numbers for RX, LX and RX,LX-LC switch kits for field installation?

Resolution: The attached table shows the part numbers for LX-RX and LX-RX-LC switches field installed.:

Can you field install a RX switch on the 24/25 device?

Resolution: The RX switch can be installed at the factory when device is ordered or in the field with part# 650359-00. Installation instructions here will show how the RX swi...:

What is the part number for the dogging assembly for a 1690/1790/2390?

Resolution: For any device made after 2001, the part number for the Falcon 1690 dogging kit would be KIT.1197 For devices made prior 2001, the dogging kit is no longer available and a new device must be ...:

What is the Ives invisible latch replacement for the Glynn Johnson AA, BB and AP2 latches?

Resolution: The Ives version is the same as old Glynn-Johnson versions.:

Where do I install my Auxiliary Fire Latch (AFL) in a Less Bottom Rod, Fire Rated (LBR-F) exit device?

Resolution: Installation should be 6" from bottom of the door. See attached templates as reference. T-5494 for HM Doors W-5494 for Wood Doors:

Ask your question Entering your question as a complete sentence will provide more accurate results than keywords or phrases.

“ auxiliary bolt field replacement kit ”

RELATED FAQS