are Von Duprin trims supplied with cylinders

RELATED FAQS

Question
Answer
You must use the drive bushing that is supplied with the 179L control trim.  It is different from teh 1790 bushing.
Step 3 and 4 of 179L Instructions will show the old drive bushing being removed & the new drive bushing getting installed
The 914KIL-IC trim is shipped with a Small format interchangeable core (SFIC) in a 6 pin "A" section/keyway.  A comparable core from Falcon would be the C646 (uncombinated - no pins) or C...
The Falcon C987 cylinder can be ordered with the #27 cam as it has a similar profile to the Schlage B520-731 cam for trims after 2/28/2011.
The standard cylinder keyway that comes with the 914KIL trim is a Schlage 6 pin "C" section.
Devices built After 2/28/2011: Use a 1 1/8" - 1 1/4" mortise cylinder with straight narrow cam. (Cam profile same as the Schlage B520-731, see table below for part numbers) Devices built Befo...
 Modular 1-1/8"  Modular 1-1/4"  SFIC and FSIC  Non-Modular Non-IC Conventional  Non-Modular Non-IC Everest Primus  B520-730  B520-731  B520-2...
The Monarch KIL trim uses the following cylinders: Schlage Cylinders 23-013 Conventional 20-750 Primus 20-750-XP Primus XP 20-550 Primus UL437 20-550-XP Primus UL437 XP Falcon Cylinder A23165-0...
A 1 1/4" mortise cylinder with straight cam (similar to the Schlage B502-191) or a 1 1/2" mortise cylinder with straight cam using supplied spacer collar. Cylinder length does not chan...
A 1-1/8 through 1-1/2" mortise cylinder with straight cam per Step 4 of 512NL Instructions.
For standard (non-IC) cylinders, use the Falcon #4 straight cam For IC cylinders, use the Falcon #5 cam 
Von Duprin does not supply cylinders keyed alike.   Cylinders keyed alike are available from Schlage and Falcon.
 The tailpiece of the rim cylinder can be inserted into the Von Duprin 98/99 rim device either vertical or horizontal.
Part numbers for Schlage and Falcon cylinders for Von Duprin devices are listed below. (KIL = Key In Lock) SCHLAGE   Mortise Rim KIL ...
FALCON   Mortise Rim KIL Conventional 986 x #4 cam 951 A23165-02 Small Format Housing C987...
If unclear whether mortise, rim, or key-in-lever is needed, reference links below to determine what cylinder type is needed.  In order to determine cylinder type needed,  you must first k...
All Von Duprin 370 Series trims require a 1 1/4" mortise cylinder with a straight cam.
No, the 98/99 series mortise exit device should be ordered as NL less trim. IE, 9875NL-L/TRIM. NL-OP suffix is normally used with the 98/99 series rim, surface and concealed vertical rod devices wh...
The Von Duprin RX996L trim was released to standard order entry in May 2010. The Von Duprin 996L and 996L-BE trims can be ordered with RX switch. The 996L-NL and 996L-DT trims can not have the...
Von duprin will supply the 996L and 996L-BE trims with RX switch. Von Duprin will not supply the 996L-NL and 996L-DT trims with RX switch because the switch monitors the lever movement and the leve...
A 1 1/4" mortise with straight cam similar to the Schlage B502-191 is needed when using Von Duprin 9975 mortise device with 996L-M trim.