Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
Are Latch guards UL listed
”
RELATED FAQS
Question
Answer
PLASTER GUARD
Resolution:
Dust Cover Box, Masonry guard, Mortar Guard, Plaster Guard.; Grout Guard:
Why should you use the LX switch with an ALK being used in Von Duprin surface vertical rod devices?
Resolution:
An RX switch would only trigger the ALK Alarm Kit when the pushpad of the device is depressed.Surface Vertical Rod (SVR) Devices such as the 2227, 33/3527A, 98/9927, and 98/9957 devices could be op...:
LGO-4
Resolution:
Extended latch guard only 4' (1219mm):
How long is the RGO?
Resolution:
The RGO (rod guard only) is 36" long x 1-5/8" wide.:
What is the difference between the Ives 482B and the 482A door guards?
Resolution:
The difference between the Brass version 482B and the Aluminum version 482A is the size and design as well as the base material and available accessories. The Brass version 482B comes w...:
EXTENDED LATCH GUARD
Resolution:
LGO, LGO-3, LGO-4:
What exit device is weather rated?
Resolution:
The Von Duprin 98/99 rim and 98/9927 surface vertical rod exit devices are now available with the Outdoor Defense (OUT) option.Devices with the OUT option have a specialized coating applied to mech...:
LATCH GUARD
Resolution:
RG-27 (LG):
Can the 2670 be cut down to fit smaller door widths?
Resolution:
The 2670 Guard X device can't be cut down to fit doors less than 3 feet. This device is designed to fit doors 36"- 48" in door width.:
How to replace the circuit board or horn on a Guard-X device?
Resolution:
See PCB replacement instructions. The horn is part of the board and can only be replaced by replacing the entire board.:
Does Von Duprin offer any pulls that through bolt to the Guard-X device?
Resolution:
Von Duprin does not offer any lever trim or pulls that through bolt to the Guard X device. Ives has the 8102-6 and 8105-6 pulls that can be lined up with the mounting screws of the exit device b...:
After replacing the battery on a Von Duprin 2670 Guard X why would the horn stop working?
Resolution:
Replacing the battery on the 2670 should not cause the unit stop working. Make sure the spring that provides tension on the plastic finger is not bent out. The spring should be at a 90 degrees...:
What is the part number for the pcb board on the 2670 Guard X exit device?
Resolution:
The following are part numbers for 2670 Guard X exit device PCB: pcb.10018 for English pcb.10019 for Spanish pcb.10020 for French:
Is the Von Duprin Guard-X exit device fire rated?
Resolution:
The Von Duprin Guard-X exit device is not fire rated because the deadbolt is not spring loaded. Therefore, there would be no positive latching as required on a fire rated opening. :
Where is the catalog information and specifications on the Ives edge guards?
Resolution:
Information for Ives edge guards can be found on pages B51-B53 of the Ives Catalog linked here, and in the edge guard ordering guide linked here.:
What is the 022558-000-70?
Resolution:
The Falcon T series was discontinued August 12th, 2026 and was replaced by the Falcon TM series. DISCONTINUED: The Falcon T lock had a reinforcement kit for a 1 3/4" thick hollow metal do...:
Is the 2670 Guard X fire rated?
Resolution:
The Von Duprin 2670 Guard X is used only on non fire rated doors thus is not fire rated.:
Why would the 996L trim not lock or unlock when installed with 98 or 99EO?
Resolution:
The 98/99 rim and vertical rod exit devices are shipped with NL drive screw to function as a Night Latch. To convert the device to Class Room, remove the NL Drive Screw on 98/99 center case ass...:
What strike is required when using the 2670 Guard-X on a pair of doors?
Resolution:
With a mullion: Use the standard strike 267 With no mullion and inactive leaf being held closed with flush or surface bolts: Use the 2609 double door strike :
Is there an electric strike that will work with the 2670 Guard X?
Resolution:
The Von Duprin 2670 Guard X does not have a spring loaded latch bolt, it is a dead bolt and will not operate with any electric strikes.:
Can Steelcraft doors be prepped for the 98/9949 Concealed Vertical Cable Exit Device?
Resolution:
Yes, as an option, Steelcraft doors are available with factory prepared for the 98/9949 Concealed Vertical Cable Exit Device.L, B, CE, T and CE-Series doors are available factory preparedDoor prepa...:
What is the RU lock?
Resolution:
The RU series from Falcon is a pre-assembled unit lock designed to retrofit existing unit locks manufactured by Falcon, Corbin Russwin and Yale. It exceeds ANSI Grade 1 specifications and is ...:
What finish will the strike and latch be if ordered with a split finish?
Resolution:
The door handing determines the finish of the latch and strike. Left reverse and right reverse doors default to outside trimLeft and right hand doors default to inside trimIf lever and ro...:
LGO-3
Resolution:
Extended latch guard only 3' (914mm):
..
Resolution:
..:
ROD GUARD
Resolution:
RGO, RG-27, RG-27-3 , RG-27-4:
LGO
Resolution:
Latch guard only:
...
Resolution:
...:
Does the Ives 482 Door Guard come with a rub plate?
Resolution:
The Ives 482 does not come with a rub plate. The brass 482 Door guard (also called 482B) comes with an edge guard or plate that is applied with adhesive to protect the edge of the door.T...:
What is the difference between Panic Hardware and Fire Exit Hardware?
Resolution:
The most obvious difference (in the device) is the lack of mechanical dogging on a Fire Rated Device. There are some internal parts that may be different and the method it is secured to the d...:
...
Resolution:
...: