ad/co lock literature

RELATED FAQS

Question
Answer
Customers will need to use the Schlage Utility Software (SUS) on the HHD lock programming device to set the desired magnetic track to be read for access control, if not using default Track 2&n...
 See the attached Technical Note for instructions on saving a "Device Template" FROM a device or loading TO a device, Device Template Tech NoteOn the SUS/HHD go to the LOCK Properties tab, and sele...
The AD and CO locks both have a 3 hour fire door rating. Please see URL for more info.  UL Fire Rating List
ALWAYS put the PIM400 in LINK mode first. On a PIM400-TD2 press the LINK1 Button for door one, and LINK2 button for door 2. With a PIM400-485 you must use the SUS/HHD to select which door to...
1. To put the AD400 in LINK mode, hold down the RTE (Lever or crash bar see below) and press the # key on the key board, or present a card to the reader.       ...
2. AD400 requires a Request To Exit (RTX) signal to link - see the user guide instructions for the linking process.    For an AD400 to enter link mode, it must see the RTX...
   3. Check the AA battery level, if the AA batteries are below 4.7 volts the AD400 can fail to LINK.             Ins...
4. PIM400/AD400 COM400 plug could be damaged! The small pins in the Main PCB board connection for the RF COMM board can get bent during installation of the RF COM400 board. If the PINs are be...
1) Make sure the lock batteries are more than 4.0 volts. The USB connection will not detect or communicate with a voltage lower than 4 volts. Many times a firmware update will draw d...
2) Make sure the SUS/HHD is set to communicate using USB connection mode in SUS.  You should see the familiar USB symbol on the SUS main Screen in the bottom right corner.  If you see a S...
3) When you update with NEW firmware replacing very OLD firmware a S1 RESET is suggested after the update. This initializes all the AD-Series memory locations to the new firmware. S1 is the ...
4) Make sure the HHD-USB cable is securely inserted into the HHD and into the lockset.  
5) Inspect the HHD-USB connector(s), ensure no pins are damaged, recessed or out of alignment. If a damaged cable is found customers should see their dealer for a replacement or they can order a re...
5) If working with a CO lockset, the mechanical key switch needs to be in its "Inactive" or normal position.  Ensure the triangle alignment on the front escutcheon and that...
Installers have reported that their AD-CO Series cylindrical or mortise locks will unlock whenever the outside lever is lifted.    This will occur if the outside spindle (square post) is install...
The minimum door thickness that the AD or CO series lock will mount on is 1 3/8".  Be advised that this will require additional spacers to be ordered separately to allow the lock to mount...
Information on low battery threshold and nuisance delay is noted below: New firmware now has improved levels. - These are approximate values/levels which change with measurement meters and measure...
AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 4 Battery Holder New batteries = 6.2 VDC Low battery threshold is 4.7 VDC for SM & MT - and 3.7 VDC for MAG and PROX (USB stops working at 4...
    AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 8 Battery Holder New batteries = 12.4 VDC Low battery threshold is 7.2 VDC Critical battery threshold is 6.9 VDC Coin cell = new/...
CO2004 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
CO2504 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
  CO200 & CO250 Disable coin cell Nuisance delay and blink, With CO.A.7 and SUS 4.10.2 or newer for CO200 and CO250, you can use the SUS/HHD, under Lock Properties, Edit, to de-select, DISABLE, t...
The part number for the AD or CO twisted tailpiece kit is: 46929303 Tailpiece Kit - (for Exterior Escutcheon -993 into Exit Device, i.e. Von Duprin 98 or 99) Exit Trim 46929303 Includes the...
As of June 2019, all ND, NDe, AD CYL and CO CYL levers are the same.
Between January 30, 2017  June of 2019, the AD and CO cylindrical lock levers were incompatible because of the ND / NDe lever and spring cage design change in January of 2017.Prior to January ...
ALL AD and CO products are warranted for electrical for 1.0 year after installation OR 2.0 years after manufacture. The mfg date is on the lock stickers AND can be viewed electronically with th...
The coin cell for the AD and CO family of electronic lock products is a 3vdc lithium. CR2025 is the specified part number.
When the SUS and HHD are used in the “Auto Update” mode, the audit info will be automatically gathered each time the SUS is successfully connected with a lock.
During the rehanding of an AD-Series Exit (993) device or the rehanding of a CO-Series Exit (993) device it is possible for the customer to damage the 5-inch pcba by using the wrong screws.  D...
All Schlage/XceedID wiegand proximity readers currently understand: -ASK (Amplitude Shift Key) - Used in GE/CASI -FSK (Frequency Shift Key) - Used in HID Prox, AWID, and Lenel The third proximit...
ISOX card technology is no longer supported - contact XceedID sales
Use a multi-meter in series with the batteries to measure battery current.  Be sure your multi-meter can accurately measure very low current, in the micro-amp range. See the attached Technical Not...
This information can be found at the following URL's: AD200 http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/UserGuide/Schlage_AD-200_Offline_Lock_User_Guide_-_English_102107.pdf
AD250 http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/UserGuide/Schlage_AD-250_Offline_Lock_User_Guide_-_English_102108.pdf
AD300 http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/UserGuide/Schlage_Utility_Software_User_Guide_6.4.2_104390.pdf
AD400 http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/UserGuide/Schlage_AD-400_and_AD-401_Networked_Wireless_Lock_User_Guide_104387.pdf
CO100 http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/UserGuide/Schlage_CO-100_Offline_Lock_User_Guide_-_English_104210.pdf CO200 http://us.allegion.com/content/dam/allegion-us-...
CO250 http://us.allegion.com/content/dam/allegion-us-2/web-documents-2/UserGuide/Schlage_CO-250_User_Guide_English_104208.pdf
This information can be found at the following URL's: AD200/AD250/AD300/AD400 Cylindrical http://w3.securitytechnologies.com/irstdocs/installinstructions/102104 P516-092.pdf
AD200/AD250/AD300/AD400 Mortise http://w3.securitytechnologies.com/irstdocs/installinstructions/102106 P516-093.pdf
AD200/AD250/AD300/AD400 Cylindrical Exit http://w3.securitytechnologies.com/irstdocs/installinstructions/102264 P516-094.pdf
AD200/AD250/AD300/AD400 Mortise Exit http://w3.securitytechnologies.com/irstdocs/installinstructions/102263 P516-095.pdf
CO100/CO200/CO250 Cylindrical http://w3.securitytechnologies.com/irstdocs/installinstructions/104214 P516-266.pdf
CO100/CO200/CO250 Mortise http://w3.securitytechnologies.com/irstdocs/installinstructions/104213 P516-267.pdf
CO-Series Cylindrical Exit http://w3.securitytechnologies.com/irstdocs/installinstructions/102297 P516-268.pdf
CO-Series Mortise Exit http://w3.securitytechnologies.com/irstdocs/installinstructions/102296 P516-269.pdf