Resolution:

Once you are enrolled on a SmartCard you can use it to access a unit that has been Cold booted (no users in memory)

 

The template and user ID are also stored in the unit -after you are enrolled and after you use a SmartCard on an empty unit.  This enables time zone and user restrictions.  You must however present the SmartCard.

Step 1:    Cold Boot the unit.

           

A.    While power is disconnected

B.     Flip DIP switches 4&5 to the ON position (toward inside of unit) (For new readers push the white reset button while applying power)

a.       this will erase all users stored in the reader

b.      will enable the first user to enroll without a supervisor

C.     Apply power

D.    Wait for the unit to boot the display will read     READY (For newer reader it will ask you to hit 1. for SETUP and 9. for ALL. Choose 9

Step2:     Enroll Supervisor

 

A.    Push CLEAR and ENTER simultaneously

a.       Note: If you did not Cold Boot, you will get an * on the display

-          this is telling you that a supervisor is enrolled

-          if a supervisor is not enrolled start over with a Cold Boot

 

B.     Display: ENTER PASSWORD               

a.       push 4 then push ENTER

 

C.     Display: ADD USER?                             

a.       push no

 

D.    Display: ADD Supervisor?                                  

a.       push yes

 

E.     Display: ID#?       

a.       Insert Smart Card into holder

b.      Type in an ID number (select the ID number yourself) and hit Enter

c.       Place hand three times

 

F.      Display: ADD USER?

a.       To add additional users go back to instruction C and select yes

b.      To exit push CLEAR

 

Step 3: Change your authority level to 5

 

1. Display: ADD USER?

a.       To add additional users go back to instruction C and select yes

b.      To exit push CLEAR

 

2. Press Clear and Enter

 

3. Display:  “*”
1. Enter ID number of enrolled manager (keypad only) and press enter
2. Verify

 

4. Display:  “Enter Password”
1. Press 5 , press enter

 

5. Display:  “Set user data”
1. Press #

 

6. Display:  “Set user auth”
1. Press #

 

7. Display: “ID # ?”
1. Enter ID number of enrolled manager (keypad only) and press enter

 

8. Display:  “Auth (0)”
1. Press 5, press enter

 

9. Press clear, clear, clear to exit menu

 

10. Update managers card
1. Place managers card in the card holder
2. Display: “Place Hand”

                                                              i.      Verify

3. Dispaly “Remove Card”

                                                              i.      Remove card

 

11. Repeat step I a second time

 

 

Step 4: Reboot (optional)

In practice after the supervisor is enrolled the units are powered off, dipswitches 4&5 are put in the OFF position and power is reapplied.  This will keep the all the users stored in memory and will not allow a new user to enroll himself if power is lost.

 

A.    Disconnect power

B.     Flip DIP switches 4&5 to the OFF position (toward outside of unit)

a.       this will prevent users records stored in the reader from being deleted

b.      will requires supervisor for enrollment (depending upon access levels)

C.     Apply power

D.    Wait for the unit to boot the display will read     READY

 

Step 5: Enroll New Users

 

A.    Push CLEAR and ENTER simultaneously

a.       Note: If you did not Cold Boot, you will get an * on the display

-          this is telling you that a user is enrolled

-          to proceed, enter supervisors SmartCard and verify

-          if no supervisor is enrolled start over with a Cold Boot

 

B.     Display: ENTER PASSWORD               

a.       push 4 then push ENTER

 

C.     Display: ADD USER?                             

a.       push yes

 

D.    Display: ID#?       

a.       Insert Smart Card into holder

b.      Type in users ID number and hit Enter

c.       Place hand three times

 

E.     Display: ADD USER?

a.       To add additional users go back to instruction C

b.      To exit push CLEAR