Falcon

Question
Answer
The Falcon S lock was replaced by the W lock (knob series).
Falcon has a 10 year warranty for its portfolio of locks.  The new warranty is in effect for all locks purchased since November 1st, 2008Electronics/electrified functions will h...
The Falcon MA mortise lock is available with an occupancy indicator on the following functions: MA301, MA311, MA321, MA371, MA431, MA441(inside of door only), MA451, MA541, MA57...
Related solution: Is the MA indicator available separately? 
The lock case can be re-handed, however, this requires opening up the lock case. See M lock re-handing instructions for a complete guide.
The old Falcon M lock had 2 lever styles that were very similar in appearance; the Kim and Sutro.   The Kim lever was hollow with a plug on the end of the lever while the Sutro was solid (alumi...
Most locks will have a standard door range they will install on, but occasionally customers will want to use them on thicker doors.  In order to do so, the extended door thickne...
Effective Feb 25, 2008 Falcon no longer offer a 612 finish on any product.
This is in regards to the California State Reference Code, (Formerly Title 19, California State Fire Marshal Standard) stating that all levers with returns comply; levers must return to within 1/2"...
The MA was launched 4/1/10 and replaced the Falcon M lock. Newer Marketing Bulletin added on 4/26/2010 (Some items not yet available!!)
SET OF FINISH SAMPLESPart number "20"One (1) of each finish on 1-1/4" diameter disks attached together with a bead chain.Finishes Included: 605, 606, 613, 619, 622, 625, 626, 630, 643e
Here are some of the major differences between the M and MA-Series.  Lever mounting post holes -  Locations have changed on door template.  (12 and 6 o'clock for M lock, MA lock is approx 1 and...
A zero bitted Falcon SFIC core is combinated for the control key to be cut at all 4's.
Replace the device and vertical rods with the current 2390 device and possibly a filler plate. A filler plate may be needed as the older 1390 device was sized per order whereas the 2390 is onl...
Key in lever Falcon cylinders do not work in Schlage locks.  The cylinders may fit, but there are no specific tailpieces created to operate any Schlage lock. SFIC SFIC is universal so Falcon and...
   Hotel cylinder in L9000 As long as the correct cam is used (Schlage clover), a Falcon Hotel cylinder will properly function in an L9486 hotel lock.
A control key is required to install or remove an interchangeable core from a housing or lever. The control key is identified by having "CONTROL" stamped on the bow. How to install and remove an i...
Only the lever return spring is available.
Related solution: What is the part number for the lever return spring for the old M series mortise lock?
BHMA provides a certified products directory complete with function codes and meanings from most of the major lock manufacturers.  The most up-to-date directory can be accessed through th...
See attached Cross Reference Chart which was available in the 2007 Price Book that will convert the older 4-digit trim numbers.
The current 712L/912L (after 2/28/2011) can be field converted by purchasing the NL Spring part #600339 and following the L to NL function change instructions.
810NL and it is the same as the old P1445 trim number.
Falcon manufactured an EZF101 which was a large plate with a recessed lever for use in elevators.  This item is no longer available.     
Falcon is reintroducing the lever return spring for the discontinued Falcon M mortise series.  Effective November 1, 2014 the lever return spring is now available for purchase with a list pric...
Falcon (19. 24, 25, and XX) parts manuals for Exits are downloadable on the 
The storeroom lock function is described as follows: Latch bolt operated by key from outside or by operating inside lever. Outside lever is always inoperative. The following are storeroom functi...
It is not possible to key SFIC and standard cylinders including Schlage FSIC into the same system.  A keyway name may be shared between the two key fami...
These parts are no longer available.  For reference the spring part number is 4841 and the clip part number is 4326.
Regular Core (suffix keyway to number) Description Uncombinated Combinated 6-Pin 7-Pin 6-Pin 7-Pin Standard C646 C647 C606 C607 Best style capping CB846 CB847 CB...
See Step 3 of the mortise lock reversing instructions(D-4010) which shows function conversions and what part(s) are needed if any are needed.
See the installation instructions 718 for -C devices.
Templates for current 718 series trim can also be found on Falcon website
To remove the M lock trim follow the steps below in reverse.       The M lock spanner wrench is 021415.  Although this wrench is no longer available from&n...
The 2390 is only available in two sizes, a  21"(overall 24.125" w/ endcaps) and a 24"(Overall 27.125" w/endcaps) unlike the older 1390 which could have been ordered to size. You woul...
All extended warranty requests are handled by Allegion Warranty Service Team.  Email Requests to warranty.service.requests@allegion.com.   
The Falcon M series was discontinued 3/31/10 and was replaced by the Falcon MA series.
The 718NL replaces the 710NL and the 718DT replaces the 710DT.  
The Falcon W replaced the Z lock in July 2006.  The Z lock was a cylindrical chassis.
Beginning in January 2015, to specify the X series as corrosion resistant, specify "SS" after the function. For example: X581 SS PD TG 630.Prior to January 2015, corrosion resistant was specified a...
The "SS" option provides a stainless steel (non ferrous) constructed chassis that when paired with stainless steel trim, provides a Grade 1 lock that is resistant to corrosion when exposed to moist...
The Falcon W-series lock has replaced the Falcon F-series and the Falcon Y-series.
There is an inspection sticker placed on the Motor of the Motor/gear box assembly and also on the top of the transformer on the control box.  This inspection sticker has the manufacture date, ...
Tubular Locks: Tubular locks have a center spindle assembly that extends through the center of the lock body and latch, allowing for retraction of the latch when the lever or knob are rotated....
The Falcon MA will not fit a 1-3/8" thick door. 
OHC 100 is adjustable from size 3-5 and is NOT ADA compliant.OHC 101 is adjustable from size 1-3 and IS ADA compliant.
You can view and subscribe to the channels below. LCN  Schlage  Steelcraft  VonDuprin  Falcon
The B571 / D271 indicator deadbolt is a Grade 2 privacy deadbolt with indicator designed to be opened with an emergency key.
Common problems in new installation: Line of sight between transmitter and receiver OR programming the transmitter to the receiver. Fix line of sight by relocating transmitter, receiver or both. Fi...
Contact you local authorized Allegion Distributor for all Allegion brand logo information.
MACS or Maximum Adjacent Cut Specifications for cylinder pinning refers to the maximum variance allowed between one pinned chamber and the adjacent pinned chamber. MACS vary from one manufacturer t...
Cylinder pin information is very unique to the device and application and requires a unique solution. If you have questions related to cylinder pin, please e-mail your request (including a descript...
Backset dimensions will vary depending on the device, application and the opening configuration. If you have questions on specific device backsets, please e-mail your request (including a descripti...
Using Soss hinges with closers can require special device and preparation locations. If you have questions on specific closer applications, please e-mail your request (including a description ...
Closer selection depends on many variables, see attached documentation explaining the many variables and options available for a closer.  We recommend you contact Product Support at ...
Falcon T series locks should only have 180 degree key rotation. If a customer has 360 degree rotation (T351, T381 (inside), T561, T571), the lock is out of time.
The Falcon T381 outside should only have about 90 degree key rotation (to retract the latch). The inside should have 180 degree rotation.
For Schlage electrified mortise and cylindrical locks, use the following table as a general rule for maximum wire length and wire gauge to be used.This chart shows the wiring sizes and lengths for ...
Please contact the Allegion Product Support Team on all questions or inquiries pertaining to hardware finishes warranties. Please send an e-mail to the applicable Product Support team:Closers_TechP...
UL listings can be searched at UL.com under Online Certifications Directory.
Apartment Corridor Lock function is defined as a lock where the latch bolt operated by lever from either side, except when outside lever is made inoperative by a stop or mechanical means other than...
The programming processes for Allegion devices can be both product and features specific.  Some products programming processes are electronic in nature, others are physical in nature. &nbs...
Discontinued in 2010.  Falcon made a trim kit to retrofit new Falcon lever hardware onto various pre-existing competitor’s mortise locks, where the current knob trim needed to be replaced (to ...
Falcon has replacement screw packs and pinion caps available for the SC series closers.  For a complete list, click here.
The MA641 installed without the thumbturn is the closest replacement for the M631.
Governments around the world are focusing on restricting and eliminating the presence of hazardous materials in products and packaging from the environment to improve the sustainability of our plan...
For information on the American Iron and Steel requirements, please contact material.declaration@allegion.com.
As of March 25, 2015LD SAR Less Cylinder, Sargent (10L + 11L), 6 Pin KIL JD SAR Less Cylinder, Sargent 6300, 6 Pin FSIC JD CO6 Less Cylinder, Corbin 8000, 6 Pin FSIC JD C07 Less...
Older Falcon mortise locks had an option with a latchbolt assembly that had a nylon insert. This latchbolt assembly was discontinued in 1993. 
Although Schlage recommends using mild soap and water for cleaning the finishes on locks, a list of common hospital cleaning agents and their possible effects on anti-mocrobial finish can be found&...
Falcon K Cylindrical LockIntroduced in the late 3rd quarter of 2015Three lever styles (Dane, Avalon, and Quantum)Available in 626 & 613 finishes.Available in a limited number of keyed and non-k...
The 4000 series cylinders previously offered with Falcon XX and 19 device series/trims or sold separately will be discontinued effective October 5, 2015.  Going forward, Falcon standard G keyw...
The Allegion Connect harness insulation is 3/8" in diameter. The Molex connector at its widest point is 0.633" (just over 5/8"). Harnesses with connectors on both ends would require a minimum openi...
There is currently no 3/4" throw latch available for the Falcon K cylindrical lock. 
Split finishes are allowed on the Falcon B, D100, D200, H2, K, MA, RU, T, W, X
UL 294 is a standard for Safety Access Control System Units.  These types of devices must be able to make a decision.UL 1034 is a standard for Safety Burglary-Resistant Electric Locking Mechan...
Schlage D, L9000 and ND-series electrified locks are not currently listed to UL1034.Falcon MA, RU and T-series electrified locks are not currently listed to UL1034.
UL294 is not applicable to Schlage D, L9000 and ND-series electrified locks.UL294 is not applicable to Falcon MA, RU and T-series electrified locks.
Falcon Pinning kit contents can be found here. 
The handing of a lock is important in order to ensure that the correct side of the door is secure, the levers are oriented properly, and that the door closes properly.  There are 2 parts to a ...
The A01407 was an old Falcon Installation tool for Interchangeable core, now discontinued.
Please see here for prep difference between the Falcon H and Falcon H2100 lock. 
Von Duprin Rod Guards (RGO's) can be used on Falcon 24-V, 25-V, 19-V, and XX-V devices.They cannot be used on WS98/9927 or WS98/9957 devices.
The MA911 is not a handed lock case. 
There is no current option to replace the D89BK. This was a deadbolt with a 2" handicap thumb-turn inside and a blank occupancy indicator on the outside.
The H2101 is not available with a full size interchangeable core from Schlage.  
The hex nut part number for the 945 Falcon Cam Lock is 031100-000-30. 
24 R new center case #650234-00 and new cover #650249  (specify finish).  
The 3H stamped into the face plate of the Falcon B and Falcon H lock means 3-hour fire rated. 
The device must meet minimum of 100 hrs., standards:  ASTM  B117Falcon organic finishes (powder-coat, e-coat, etc.) are only certified to 96 hours.  Falcon inorganic finishes such as...
A rim cylinder is required for rim and vertical rod XX devices.  A mortise cylinder is required for a mortise lock XX device.
You could use:Falcon: 25 R 512NL,  or Von Duprin: 98NL 990.
The device is handed but field reversible as shown here in step 11 of the installation instructions.
8' max  height on UL fire rated F-25-R
For the 25 series, the LM or DM kit is field replaceable, but not field installable.  There are 2 holes that must be drilled in the center case at the factory for those switch kits.
Yes.  The Falcon 510L FSA/FSE be converted in the field?Click Here for details. 
Depends on the combinating rule and the number of pins (chambers).   For A2  6 pin systems = 4,096 changes For A2 7 pin systems = 16,384 changes   For A4 6 pin systems = 15,625 ...
The C261 and C264 are no longer offered. The C262 RH 1-5/8" can be used in place of C261 RH 1-1/2".The C265 LH 1-5/8" in place of the C264 LH  1-1/2"
A30771-000-00 is a tailpeice package that is shipped with a Falcon T lock when ordered with "BDC" cylinder suffix, and cannot be ordered seperate. 
The Steelcraft Paladin Series doors and frames are available in compliance with FEMA 361 and ANSI ICC500-2014.  The door system may include other approved Allegion hardware and components that...
Yes, fire rated exit devices can have electric latch retraction.  However, the devices must be tied into a fire alarm system to remove power from the units so the doors will be latched in the ...
The Falcon K lock does have the clutching feature. 
The Falcon T lock comes standard with the "Pressure Release" feature which is more commonly known as clutching. 
The Falcon D871 indicator plate was a square shaped plate.  The part number for the indicator was 009151-001.The D800 series is no longer offered nor are parts. It was replaced by the D200 ser...
The pull is furnished with shoulder bolts and set screws that affix the trim to the pull side of the door.  The trim does not through bolt to the door.