firmware release notes

RELATED FAQS

Question
Answer
Information on low battery threshold and nuisance delay is noted below: New firmware now has improved levels. - These are approximate values/levels which change with measurement meters and measure...
AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 4 Battery Holder New batteries = 6.2 VDC Low battery threshold is 4.7 VDC for SM & MT - and 3.7 VDC for MAG and PROX (USB stops working at 4...
    AD400/AD200/AD250 After ADFwPkg 2.17.0 - June 2011 8 Battery Holder New batteries = 12.4 VDC Low battery threshold is 7.2 VDC Critical battery threshold is 6.9 VDC Coin cell = new/...
CO2004 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
CO2504 Battery Holder (ONLY) New batteries = 6.2 VDC Low battery threshold is 4.2 VDC Critical battery threshold is 3.9 VDC Coin cell = new/full is 3.0 VDC, low is 2.8 VDC
  CO200 & CO250 Disable coin cell Nuisance delay and blink, With CO.A.7 and SUS 4.10.2 or newer for CO200 and CO250, you can use the SUS/HHD, under Lock Properties, Edit, to de-select, DISABLE, t...
When new product(s) are added to an existing installed customer site, all devices at that site should be updated to the latest firmware revision that is available.  Whenever an AD-Series&nbs...
 
 
 
When new product(s) are added to an existing installed customer site, all devices at that site should be updated to the latest firmware revision that is available.  
 Whenever an AD-Series credential reader is upgraded with new or different credential types or replaced in the field, be sure to update the firmware so that the main and reader have com...
For the most consistence product operation all device firmware revisions should match the new product being installed.  
Ensuring consistent firmware revisions across your facility will guarantee that all of the installed customer products will act and respond the same durng use and programming.  
Products updated with the latest available firmware will also include the latest feature set(s), improvement performance and/or bug fixes  
Go to the Schlage support site to download the latest firmware package  - www.schlage.com/support  
Steps to determine what firmware version your products are currently using AND if a firmware update is suggested: Use the Hand Held Device (HHD) and Schlage Utility Software (SUS) application to...
  1) RS-485 communication will NOT interfere with a new firmware update on an AD300. You do not need to disconnect the RS-485 wires from the AD300. The AD300 will not be onlin...
  Steps to update firmware on an AD300. A) Keep the VIN/GND or AUX power applied. The AD300 will not function properly on AA battery power. B) Connect the SUS/HHD to the USB connector and p...
CO-100 now allows the PIN code length to be changed manually.  Each CO100 has a label that indicates its firmware revision.  Firmware revision 2.5.0 or higher support these...
CO-100 PIN length can range from 3 digits to 6 digits with firmware version 2.5.0 and higher.
Procedure to change PIN length: 1. Press {programming code (default is 97531)} then {*}.2. Press {99} then {*}, to enter Special Function Length Menu.3. Press {4} then {*}, to enter Pin Length M...
CO-100 now has NEW lock status reporting capabilities. Battery status, firmware version, hardware version and PCB serial number. See instructions below for these status menus.
ADFwPkg 2.17.10 released 06/06/2011 is the first AD firmware Package that supports WRI400 and CT5000 devices.
SUS 4.4.0 released on 06/06/2011 is the first released SUS version compatible with WRI400 and CT5000 devices.