Category: 1790 Series

(Results from 1 to 10)
What power supply is need for Falcon EL devices?
The Von Duprin PS914 power supply with either the 900-2RS  or the 900-4RL option board is required....
Schlage Commercial » Exit Devices » Touch Bar » 1490 Series | Schlage Commercial » Exit Devices » Touch Bar » 1590 Series | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series | Schlage Commercial » Exit Devices » Touch Bar » 24 Series | Schlage Commercial » Exit Devices » Touch Bar » 24 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 25 Series | Schlage Commercial » Exit Devices » Touch Bar » 25 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 33A/35A Series | Schlage Commercial » Exit Devices » Touch Bar » 98/99 Series | Schlage Commercial » Power Supplies » Standard » PS900 Series » Von Duprin
Is the Falcon 1790 an exact retrofit for the 2090?
The 1790 and 2090 will fit the same hole pattern.  However, the 2090 latch is located lower than the 1790 when installed.   The strike can be re-located to address the issue....
Schlage Commercial » Exit Devices » Touch Bar » 1790 Series
EL Device Troubleshooting Guide
VISIT US.ALLEGION.COM/EL-SUPPORT FOR TROUBLESHOOTING VIDEO, DOWNLOADABLE GUIDE, AND INSTALLATION INSTRUCTIONS(For best viewing, use Chrome or Firefox browser.)ALLEGION EL SOLENOID ELECTRIC L...
Schlage Commercial » Exit Devices | Schlage Commercial » Exit Devices » Recessed | Schlage Commercial » Exit Devices » Recessed » 2390 Series | Schlage Commercial » Exit Devices » Recessed » 94/95 Series INPACT | Schlage Commercial » Exit Devices » Touch Bar | Schlage Commercial » Exit Devices » Touch Bar » 1490 Series | Schlage Commercial » Exit Devices » Touch Bar » 1590 Series | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series | Schlage Commercial » Exit Devices » Touch Bar » 24 Series | Schlage Commercial » Exit Devices » Touch Bar » 24 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 25 Series | Schlage Commercial » Exit Devices » Touch Bar » 33A/35A Series | Schlage Commercial » Exit Devices » Touch Bar » 33A/35A Series » Von Duprin | Schlage Commercial » Exit Devices » Touch Bar » 98/99 Series | Schlage Commercial » Exit Devices » Touch Bar » 98/99 Series » Von Duprin | Schlage Commercial » Falcon | Schlage Commercial » Von Duprin | Schlage Commercial
Are Falcon exit devices available with weep holes?
Weep holes are not available with Falcon devices. ...
Schlage Commercial » Exit Devices » Touch Bar » 1490 Series | Schlage Commercial » Exit Devices » Touch Bar » 1590 Series | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series | Schlage Commercial » Exit Devices » Touch Bar » 17 Series | Schlage Commercial » Exit Devices » Touch Bar » 18 Series | Schlage Commercial » Exit Devices » Touch Bar » 19 Series | Schlage Commercial » Exit Devices » Touch Bar » 24 Series | Schlage Commercial » Exit Devices » Touch Bar » 25 Series | Schlage Commercial » Falcon
Does the 1790EO device ship with a nightlatch cylinder assembly?
The 1790EO does not ship with a cylinder assembly. If you wish to convert a 1790EO to NL or HB operation, then you will need the 179CA cylinder assembly and a standard rim cylinder. ...
Schlage Commercial » Exit Devices | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series
What is the degree of key rotation to retract the 1792 latch bolt?
The key must turn approximately 180° to fully retract the 1792 latch bolt....
Schlage Commercial » Exit Devices | Schlage Commercial » Exit Devices » Touch Bar | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon | Schlage Commercial » Glossary » Exits
Is the RX switch field installable on the Falcon 1690, 1790, or 2390?
RX switch assembly (# SWITCH.1006) is field installable on devices shipped after a 2002 redesign....
Schlage Commercial » Exit Devices » Recessed » 2390 Series | Schlage Commercial » Exit Devices » Recessed » 2390 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series | Schlage Commercial » Exit Devices » Touch Bar » 1690 Series » Falcon | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon
For Falcon 1790 with HB hold back function, does the set screw need to be installed in the drive bushing?
Please reference step 2 of the 1790 instructions linked here.  It shows to remove the set screw, rotate the drive bushing counterclockwise, and leave the set screw out....
Schlage Commercial » Exit Devices » Touch Bar » 1790 Series | Schlage Commercial » Exit Devices » Touch Bar » 1790 Series » Falcon
Can the 179L Trim be re-handed in the field?
Yes, you can re-hand the 179L trim in the field.  The full instructions can be found here, Page 5, Step 5.  Follow these instructions:...
Schlage Commercial » Exit Devices » Touch Bar » 1790 Series | Schlage Commercial » Falcon
What are the dimensions of the 1790 HB (Hold back) set screw?
4-40 1/8" We do not sell this screw by itself.  If one is needed, we recommend purchasing it through part number: CAMASY.101...
Schlage Commercial » Exit Devices » Touch Bar » 1790 Series | Schlage Commercial » Falcon