will Schlage cylinders work in other manufacturers deadbolts

RELATED FAQS

Question
Answer
The Schlage full size interchangeable core (FSIC) prepped B560F, B561F, and B563F deadbolts all require a UL fire cup (R) in order to be UL listed.  This fire cup is s...
Falcon D series deadbolts will not accept Schlage Key-in-lever cylinders. The faceplate plug hole is smaller in diameter than the Schlage plug and does not fit flush when i...
For a Schlage "C"  keyway:  Specify "CP6" as the cylinder suffix when ordering  D100 or D200 locks (All other Schlage keyways are not available).
Schlage offers a comparable cam to the Yale 2160 and it will operate any Yale lock that utilizes the Yale 2160 cam.     Schlage Cams for Yale 2160  Part Number  Description  B520-7...
The L Series lock can fit into a door prepped for the SCHLAGE K Series with some additional prep as described here.  
K and L trim and parts are not interchangeable. 
Standard and Full Size I/C mortise cylinders on the L9485 and L9486, Hotel or Restroom Locks, use the concept of a ward ring to lock out all change keys once the deadbolt is thrown. Instead of a fu...
HANDINGA stop ring is installed on the right side for right hand operation and on the left side for left hand operation.  Right hand shown below.
The 5100 electric strikes are for use with cylindrical locks only.  Instead use the following:6211 electric strike is used with mortise lock without deadbolt on a new single door, hollow ...
The thumbturn will work but the spindles sit 90 degrees off from each other (Schlage is square, Falcon is diamond).  The result is the throw will end up 10 and 2 o'clock instead of 12 and 3. 
Here are some of the major differences between the M and MA-Series.  Lever mounting post holes -  Locations have changed on door template.  (12 and 6 o'clock for M lock, MA lock is approx 1 and...
The Schlage B and BD cylinder suffixes designate less small format interchangeable core (SFIC) cylinder prep for the lock. Any SFIC, 6-pin or 7-pin, can be inserted into the lock and will operate t...
The Falcon C987 cylinder can be ordered with the #27 cam as it has a similar profile to the Schlage B520-731 cam for trims after 2/28/2011.
Schlage only offers a limited number of keyways that match the BEST sections. Available in keys and cores.Specify keyway using the B suffix: AB = A, BB=B, CB=C, DB = D, DDB=DD, EB = E, FB = F, GB =...
The Schlage L-Series uses a clover leaf cam with the exception of the L9060 outside cylinder which uses a straight cam. The cam part number will depend on the type of mortise cylinder, keyway (for ...
You must use the drive bushing that is supplied with the 179L control trim.  It is different from teh 1790 bushing.
Step 3 and 4 of 179L Instructions will show the old drive bushing being removed & the new drive bushing getting installed
Click here for a list of available Schlage cams comparable to the Sargent 13-0660.
Schlage and Falcon double cylinder deadbolts have concealed screws to prevent tampering. The two methods used to conceal the thru-bolts are using screw caps or a faceplate. Use the below instructio...
The 9550 series Senior Swing WILL NOT work on a pair of doors with auto flush bolts. The 9560 series Senior Swing and a sequence module are required when used on an pair of door with auto flush b...
Schlage now offers modular style cams to operate the Falcon MA locks.  The following part numbers are cams for all MA locks (except the MA381): L583-638 for 1-1/8", 1-3/8", 1-5/8" length cylin...
Price Book 72A List Price $8.10
The 4610/4620 series operators are obsolete. There is no replacement part for any electronic component (motor/clutch, controller, input/output PC boards) for the obsolete 4610/4620 operators.Essent...
Key in lever Falcon cylinders do not work in Schlage locks.  The cylinders may fit, but there are no specific tailpieces created to operate any Schlage lock. SFIC SFIC is universal so Falcon and...
   Hotel cylinder in L9000 As long as the correct cam is used (Schlage clover), a Falcon Hotel cylinder will properly function in an L9486 hotel lock.
Standard Schlage cylinders will not fit in Yale locks, but Schlage does offer special retrofit cylinder that, when ordered, can fit into specific Yale locks.  See below for retrofit options.  ...
The 17, 18, & 19 devices use the same dogging assembly part #610480.
Falcon replaced its deadbolt offering in 2008 with the D100 and D200 series.  The D800 Grade 2 deadbolt was replaced by the D200 and the D400 Grade 1 deadbolt was replaced by the D100.   The new bo...
  Part compatibility (Old vs new): With the exception of the cylinder, most of the parts are neither backward nor forward compatible.  This includes the deadbolt. The cylinder mechanism for al...
The B520-698 cam was designed for a Schlage IC mortise cylinder (see Figure 1) to operate a Falcon MA lock, all functions except the MA381.  There is no Schlage cylinder option ...
The current 812L trim will replace the older 182L trim. Due to the thicker escutcheon plate of the 812L trim a 1 1/2" mortise cylinder with straight cam for mortise devices or a longer rim cylinde...
The following application information apply to the 5100 electric strike: Can only be used on a single door with a cylindrical lock Can not be used on a pair of doors Can not be used on a mullion
Schlage offers Falcon Retrofit cylinders to fit many of Falcon's locks.  Table 1 below contains part number for T series locks.  Table 1 - Falcon retrofit cylinders  
B500 with standard cylinders How to order with the deadbolt: Door thickness over 1 3/4" to 2 1/4", specify door thickness when deadbolt is ordered Door thickness greater than 2 1/4" will req...
The Von Duprin 370 series control required a 1 1/4" mortise cylinder and will not operate with 1 1/8" mortise cylinder.
Indicator not extended Indicator extended
The indicator on a cylindrical hotel lock is a small pin that projects outward from the face of the cylinder plug (Figure 1) when the inside push button is depressed.  When this pin is pr...
Warranty Statement3 Year Limited Mechanical Warranty and 1-Year Limited Electromechanical Warranty - Additional warranties listed below The provisions of these limited warranties do not apply to P...
Only the 10-079 or 10-078 strike should be used with the L400-Series.  
Standard Schlage rim cylinders will fit a total thickness of door and projecting trim of 3 inches, this includes a minimum of 3/8" of engagement of the tailpiece into the exit device.  See ima...
For total thickness measurements larger than 3 inches see the special cylinder offerings in Pricebook.  Specify the part number and include the total thickness.  We do not offer the ...
Schlage does not have a stainless steel/non-ferrous lock series. The only option that Allegion provides is the Grade 1 cylindrical Falcon X-Series. To order the Falcon X with the stainless st...
The AD200, 250, 300, and 400 trims will work with the Von Duprin 98/9975 mortise Exit Devices.