Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
will falcon cylinders work in Schlage ND locks
”
RELATED FAQS
Question
Answer
Is the C987 a small format or full size core?
Resolution:
The "C" indicates small format IC core, which is the only core style Falcon products. The C987 will be provided less core unless -6, or -7 suffix is specified (6 or 7 pin core) Example:...:
Are ND locks available in 629 or 630 finishes?
Resolution:
The AL and ND locks are not available in any stainless steel finishes. The only option is either the 626 satin chrome or 625 bright chrome.:
Is dogging available w/ EL option on 24 or 25 series devices?
Resolution:
This option is not available as the solenoid is in the mechanism case where the dogging components would go. An HD-EL solenoid is not available, and Special Dogging(SD) is not an optio...:
What is the standard Falcon cam?
Resolution:
Cams for other applications may be specified with no additional charge, see pricebook.:
Will the Von Duprin 376T control accept a 1 1/8" mortise cylinder?
Resolution:
The Von Duprin 370 series control required a 1 1/4" mortise cylinder and will not operate with 1 1/8" mortise cylinder.:
What other locks can the blue lever removal tool 24002693 be used with?
Resolution:
On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project. This tool can be used for Schlage ND-Series ...:
What non IC cam is offered by Schlage to work in a Falcon MA lock?
Resolution:
Price Book 72A List Price $8.10:
Will the standard cylinder drive bushing on a 1790 device work with my 179L trim?
Resolution:
Step 3 and 4 of 179L Instructions will show the old drive bushing being removed & the new drive bushing getting installed:
What parts are modified when ordering an ND extended lock?
Resolution:
Only the chassis components are modified for thicker door applications, the lever and spindle assemblies remain intact. The following parts may be modified depending on the function of the lock ...:
Can I put a Schlage Key-In-Lever cylinder into a Falcon D100 or D200 lock?
Resolution:
For a Schlage "C" keyway: Specify "CP6" as the cylinder suffix when ordering D100 or D200 locks (All other Schlage keyways are not available).:
What cylinder is required for the 360L from Von Duprin?
Resolution:
A 1 1/4" mortise cylinder with straight cam (similar to the Schlage B502-191) or a 1 1/2" mortise cylinder with straight cam using supplied spacer collar. Cylinder length does not chan...:
What keyway comes with the Falcon 19-KIL?
Resolution:
The standard cylinder keyway that comes with the 914KIL trim is a Schlage 6 pin "C" section.:
What is the maximum door thickness a Rim cylinder can fit on?
Resolution:
For total thickness measurements larger than 3 inches see the special cylinder offerings in the Schlage Pricebook. Specify the part number and include the total thickness. We do no...:
What is the part number for the Schlage cylinder to work in a Falcon T lock?
Resolution:
Schlage offers Falcon Retrofit cylinders to fit many of Falcon's locks. Table 1 below contains part number for T series locks. Table 1 - Falcon retrofit cylinders :
What cylinder and cam is used with the 650 series keyswitch?
Resolution:
If blocking rings (PN 36-079) are needed, specify dimensions when ordering. See below for blocking ring (PN 36-079) dimensions. Blocking RingSpecify Dimension 1//8" 012 3/16"&nb...:
What is the standard backset for the ND locks?
Resolution:
The default backset is 2 3/4" and the latch faceplate dimensions are 1 1/8" x 2 1/4". The latch supplied is the 13-047 deadlatch and 13-048 springlatch.:
What cylinder is used for the Falcon 510L and 510L-NL trim?
Resolution:
The Falcon Monarch 510L and 510L-NL trim will accept either a 1 1/4" Mortise cylinder with a straight cam or a 1 3/8" Mortise cylinder with a straight cam using the blocking ring provided with the ...:
Will a Schlage L9000 thumbturn work on a Falcon MA lock?
Resolution:
The Schlage 09-509 Rose style thumbturns will work but the spindle sits 90 degrees off from each other (Schlage is square, Falcon is diamond). The result is the throw will end up 10 and 2 o'c...:
Will a Medeco key-in-lever cylinder fit into an ND lock?
Resolution:
Medeco does offer a key-in-lever cylinder to fit the Schlage ND. You will need to contact Medeco for the cylinder Specify a key-in-lever cylinder to fit the Schlage ND lo...:
Why does my key cylinder spin and not lock or unlock the ND?
Resolution:
This could also happen if the tailpiece isn't installed in a KIL, FSIC, or SFIC cylinder. The FSIC driver also could have come loose from the core in the spindle. :
How does a Falcon Hotel cylinder operate?
Resolution:
The following document contains information on Falcon (Non I/C) Hotel Cylinders, including part numbers, key requirements and operation. Falcon Hotel Cylinders.:
What does the hotel indicator look like for the A, AL, D, and ND?
Resolution:
The indicator on a cylindrical hotel lock is a small pin that projects outward from the face of the cylinder plug (Figure 1) when the inside push button is depressed. When this pin is ...:
Does Schlage or Falcon manufacture a stainless steel cylindrical or mortise lock?
Resolution:
Schlage does not have a stainless steel/non-ferrous lock series. The only option that Allegion provides is the Grade 1 cylindrical Falcon X-Series. To order the Falcon X with the stainless st...:
Does the cam have to be inverted for cylinder dogging on the falcon 25?
Resolution:
The cam is not inverted on the mortise cylinder for the CD option.:
What cylinder is used in the Falcon 24/25 exit alarm kit?
Resolution:
The Exit Alarm takes a 1 1/8" Mortise cylinder with a straight cam. See first page of Exit Alarm inst below. Exit Alarm inst:
What replaced the D400 series or the D800 series?
Resolution:
Part compatibility (Old vs new): With the exception of the cylinder, most of the parts are neither backward nor forward compatible. This includes the deadbolt. The cylinder mechanism for al...:
Do the Falcon exit devices have the double cylinder option?
Resolution:
A double cylinder(-2) option is not available on a Falcon device but is available from Von Duprin.:
Can you use a new 812L on an old bar that had a 182L?
Resolution:
The current 812L trim will replace the older 182L trim. Due to the thicker escutcheon plate of the 812L trim a 1 1/2" mortise cylinder with straight cam for mortise devices or a longer rim cylinde...:
When ordering the ND lock less cylinder will it come with a tailpiece?
Resolution:
The Schlage ND is shipped with a driver/tailpiece when ordered with a LD, BD, or JD suffix.:
What is the Falcon cam designation for use on 25 series trims?
Resolution:
For standard (non-IC) cylinders, use the Falcon #4 straight cam For IC cylinders, use the Falcon #5 cam :
Can the Von Duprin 5100 electric strike be used on a pair of doors?
Resolution:
The following application information apply to the 5100 electric strike: Can only be used on a single door with a cylindrical lock Can not be used on a pair of doors Can not be used on a mullion:
What is the thread on a mortise cylinder?
Resolution:
The thread spec on Schlage and Falcon mortise cylinders is 1.150 x 32:
Is the dogging assembly for the 17/18 device still available?
Resolution:
The 17, 18, & 19 devices use the same dogging assembly part #610480.: