where do you add oil

RELATED FAQS

Question
Answer
All Steelcraft Frame, Door and Architectural Stick components will receive one coat of sprayed-on factory paint which is a baked-on, rust-inhibited primer that conforms to the industry standard ANS...
The fluid in an LCN closer must not be refilled in the field. See attached Warranty and Repair Communication 
The 4040(XP) door closer can be used as a temporary replacement in a 4630/4640 operator to provide manual control of the door while the 4630/4640 closer cylinder is being repaired or a replacement ...
613, Finish, US10B
The finishes below are available on the L9000, some lever designs and trims are not available in all finishes.  605  Bright Brass  606  Satin Brass  609 &...
The only routine maintenance required on a biometric hand reader is cleaning.  The platen surface upon which the hand is placed, the side mirrors, and the overhead window should be cleaned with rea...
There are a few things that can cause a closer to slam. The closer could be adjusted incorrectly. Turn all regulating screws clockwise until they stop. Then open each valve 1 and 1/2 turns. If t...
The ND40 does not have this option.  You will need to look at a mortise lock, L9496, or a deadbolt such as the B571.
To add the bottom rod and latches on 8827LBR it requires Bottom Rod Kit part #050455-XX 8827 Rod Guide Kit part #50482-XX 8827 LR Bottom Latch Kit W/Cover part #050467-XX 304L Bottom Strike
Out of the Box, or after a Factory Default Reset, all AD locks can be used in a "Construction Mode".    At launch ...   The AD-Series locks would accept the first card credentia...
Update your device firmware to the latest version to fix this early design / feature update
The 98/99 rim device can be converted to double cylinder 98-2 or 99-2. Double cylinder features an inside key cylinder which locks or unlocks the outside trim (Classroom Function) and an outside c...
If the RX switch is in the device itself yes. You can not however have both the "E" and "RX" options in the same 996L trim as both the solenoid & switch are mounted in the same place in the trim.
In late July, 2014, Schlage began taking orders for a new high visibility indicator for both N escutcheon and sectional trim applications.  A complete listing of lock functions and part number...
The L Series mortise indicator datasheet can be found here. Includes how to order.
The 643e is a powder coat finish equivalent to the US11 aged bronze finish.  The 613 is oxidized and oil rubbed and is equivalent to the US10B.
Close up of the copper relieved edges on 643e
605 Bright Brass, 625 Bright Chrome, 612 Satin Bronze, 626 Satin Chrome, 613 Oil-Rubbed Bronze, 695 Duranodic Dark BronzeClick - for listing and information about finishes.
Authentic oil rubbed bronze finish, or finish code 613 oil rubbed bronze will wear over time due to the “rubbed” finishing method which does not allow application of a protective coating or plating...
Warranty Statement3 Year Limited Mechanical Warranty and 1-Year Limited Electromechanical Warranty - Additional warranties listed below The provisions of these limited warranties do not apply to P...
If device backset is correct, replacing the device center case & center case cover with a F-24-R to add deadlocking to the latchbolt.  Parts to the F-24R center case & cover can b...
There is no EL conversion kit for a 2390, the device will need to be replaced.
When dealing with glass lights in doors, there are three (3) critical dimensions which must be coordinated: Exposed Glass Size (EGS) - the horizontal and/or vertical dimensional size of the vision...
There is no conversion kit to add EL or ED to an existing 1690 or 1790 series device. All of the components are built into the device, since the device does not have a separate baseplate.&n...
The QEL conversion kit (3' or 4') and the RX switch kit (050251-00) can convert the 9927 to QEL-RX9927 device.
The Schlage Danmark levers are not available on the Von Duprin 996L lever trim.