Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
what keyway is supplied with falcon exit devices
”
RELATED FAQS
Question
Answer
Can I put a Schlage Key-In-Lever cylinder into a Falcon D100 or D200 lock?
Resolution:
For a Schlage "C" keyway: Specify "CP6" as the cylinder suffix when ordering D100 or D200 locks (All other Schlage keyways are not available).:
Does Von Duprin supply the 9875, 9975, 9875-F and 9975-F mortise exit devices with NL-OP trim function?
Resolution:
For night latch function with pull by others, the 98/99 series mortise exit device should be ordered as NL less trim, e.g., 9875NL-L/TRIM. We will furnish a device only, and the mortise cyl...:
What is the Falcon restricted keyway process for new end users?
Resolution:
A PO from a distributor with a letter of authorization from the end user.:
Is the Falcon 1390 exit device dogging kit (4270106669) still available?
Resolution:
The Falcon 1390 exit device is discontinued and parts are no longer available from the factory. New England Door Closer may still have some older kits and can be contact...:
Can the Falcon Monarch 718C or 718NL trim be used with the 25-C exit device?
Resolution:
The Falcon Monarch 718C and the 718NL trims can be used on the 25-C exit device. The 718C trim is listed in the Price Book for the 25 series The instructions attache...:
How do you test a Falcon 24 or 25 Series EL solenoid?
Resolution:
The resistance readings for a Falcon 24 or 25 Series EL solenoid should read;Green to Yellow = Pull Coil, should measure between 1 and 2 ohms of resistance. Green to Orange = Hold Coil, s...:
What is the difference between Panic Hardware and Fire Exit Hardware?
Resolution:
The most obvious difference (in the device) is the lack of mechanical dogging on a Fire Rated Device. There are some internal parts that may be different and the method it is secured to the d...:
What is the part number for the dogging assembly for a 1690/1790/2390?
Resolution:
For any device made after 2001, the part number for the Falcon 1690 dogging kit would be KIT.1197 For devices made prior 2001, the dogging kit is no longer available and a new device must be ...:
Is the RX option the same as the old AE option on Falcon exits?
Resolution:
The AE option is now called RX (Request to Exit) to match other Allegion exit brands nomenclature. The feature of getting a signal from the pushing of the device's pushpad is the same. :
What keyway comes with the Falcon 19-KIL?
Resolution:
The standard cylinder keyway that comes with the 914KIL trim is a Schlage 6 pin "C" section.:
What is the part number for a hex dogging shaft for Falcon Dor-o-Matic 1690 or 1790 exit device?
Resolution:
The part number for 1690/1790 hex dogging shaft is shaft.101:
Does Falcon offer a Delayed Egress exit device?
Resolution:
There is not a fully self-contained delayed egress like a Von Duprin Chex-It device but the Falcon RX-24 or RX-25 Series can perform a delayed egress by using the DE5300 controller, power supp...:
What is the FA3 keyway?
Resolution:
The FA3 keyway is the ILCO equivalent to a Falcon Conventional G 6-pin keyway.:
How far down can an exit device be cut down in the field?
Resolution:
For most exit devices, please refer to the specific device series catalog for minimum door opening width the device can be cut down to fit. Be aware that some device options, frame...:
What sections are used on split keys?
Resolution:
Split key systems are delivered in the highest level section on the key tip (insert): L - obverse or classic Y - reverse 0000 - Paracentric ZZZZ - Quad D000 - restricted Everest C000 - open...:
What replaced the Falcon Monarch 17 & 18 devices?
Resolution:
Falcon Monarch 24 series exit devices replaced the 17 Series exit devices. Falcon Monarch 25 series exit devices replaced the 18 Series exit devices.:
Warranty information on Allegion Commercial products.
Resolution:
See here for our Warranty Information. :
Do the Falcon exit devices have the double cylinder option?
Resolution:
A double cylinder(-2) option is not available on a Falcon device but is available from Von Duprin.:
Can you field install a RX switch on the 24/25 device?
Resolution:
The RX switch can be installed at the factory when device is ordered or in the field with part# 650359-00. Installation instructions here will show how the RX swi...:
What cylinder is used in the Falcon 24/25 exit alarm kit?
Resolution:
The Exit Alarm takes a 1 1/8" Mortise cylinder with a straight cam. See first page of Exit Alarm inst below. Exit Alarm inst:
Where are the part manuals for Falcon exits?
Resolution:
Falcon (19. 24, 25, and XX) parts manuals for Exits are downloadable on the :
What is the part number for the EAK PCB only for Monarch Falcon devices?
Resolution:
This circuit board will NOT work on the updated 24/25 Alarm Kits that released June 11th, 2012.:
What BHMA Grade is the Falcon 25 Series exit device?
Resolution:
A copy of the BHMA Directory Listing can be viewed in the online Certified Directory on the BHMA web site. BHMA:
What is different about the updated Falcon Exit Alarm (EA) option ?
Resolution:
The Falcon Exit Alarm option was updated in June 2012 to include the following benefits. Louder Alarm 95dbs vs 87dbs Easier battery changes 24Vdc hardwire(HW) option included w...: