Steelcraft N face type

RELATED FAQS

Question
Answer
GrainTech® is a Steelcraft door option which provides a wood grained pattern which is embossed into both face sheets of the door. GrainTech doors are factory stained and top coated with a cle...
The conversion kit does not contain a new mechanism case cover plate.  If a cover plate is desired you would need the Fire or Less Dogging Cover Plate for EL conversion kit and panic cover plate fo...
Front, Lock Front
Raceway availability: Optional factory installed raceways are available in doors but are not available in frames. Preparation Info: Steelcraft installs a flexible 1/2" ID steel conduit through the...
Von Duprin doesn't offer any electric strike to fit into 1 1/2" aluminum/metal faced frame.  Minimum requirement to install 6211/6211AL is 1 15/32" mortise depth.
Exposed part of frame parallel to face of the wall
Yes, Steelcraft doors we are approved up to 48" in height or not to exceed a total 2304 square inches per face. Protective plates are usually flat sheets of metal or plastic applied to one or both...
Elevation frames are available in: F-Series (F16 or F14) FN-Series (FN16 or FN14) MU-Series (MU16, MU14) Additional parameters of the frame components: Perimeter (Head and Jambs) Frame: ...
Steelcraft does offer two types of seamless edge construction that support SDI classification standard Model 2 -seamless. Filled Edge: Epoxy fill, two part epoxy filled and dressed smooth. (LF, ...
No, Steelcraft does not offer frames with concave, cove molded faces or other simulated profiles which simulate wood trims. An options to these type of frame profiles is a frame with out return...
Reveal is the distance or measurement from the face of the door out to the face of the frame on the push side of the door.Other related terms:Door face - The exposed surface of door visible wh...
Steelcraft offers two optional types of reinforcements for open section header to be installed in distributor shop or in the field: Full profile sleeve; is a 14 gauge, 16" long part to fit the p...
If the door hits the frame (or rubs on the rabbet of the head or jamb) the frame is out of square and improperly installed. Door edge rubbing on the rabbet - shimming the hinges may resolve the...
Welded (SUA) frames: Welded frames are designed, manufactured and supplied with either square cut/notched corners or with (saw or die) miters and may or may not have connection tabs and slots. Thes...
Steelcraft does not offer doors with textured steel face sheets. Textured steel options (EP1 and EP3) were discontinued in 2000 due to lack of demand Steelcraft does offer optional GrainTech steel...
GrainTech® doors are not available with different finishes on the inside and/or the outside door panels. Both panels must match. Standard GrainTech® finishes include: Birch Ash Oak Maple Ma...
Both the DW and K-Series frames are identical with the exception of the base anchoring. Both the DW and K-series frames are supplied with a field adjustable compression anchor in each jamb located ...
Purpose: When there is concern for the weight of overhead wall construction, or, when multiple surface applied hardware components are being used. This continuous channel has the ability to spre...
Optional closer reinforcements are located at 3" from hinge jamb to the beginning of the reinforcement plate. This applies to Regular Arm, Parallel Arm, Top Jamb. Regular Arm (RA) closer reinfor...
Levels and Models (covered in ANSI A250.8 (SDI 100) "Recommended Specifications for Standard Steel Doors and Frames") are SDI term aid in the selection and specification pr...
The location to the top of hinge will vary depending on hinge size used. 6'8" Frame with 1 1/2 pair of hinges (top to top): For 4 1/2" hinges from the head to top of each hinge is 7 1/2", 37 7...
Hardware falling off a door is caused by one or all of the following issues: Field abuse Improper internal reinforcements in the door Improper field preparation The top or bottom rod case can...
The default backset is 2 3/4" and the latch faceplate dimensions are 1 1/8" x 2 1/4". The latch supplied is the 13-047 deadlatch and 13-048 springlatch.
See the Levon lever below, Figure 1. Figure 1: Levon dimensions
  The door face to lever tip distance is 1 3/8"
If mechanism cover plate causes the EL solenoid to drop when slid over the solenoid, the solenoid plunger requires adjustment.  You must lengthen the rod by turning the hex nut in front of the plun...