Allegion
Terms of Use
Privacy Policy
Frequently Asked Questions
Ask your question
Entering your question as a complete sentence will provide more accurate results than keywords or phrases.
User questions
FAQs
Category List
“
Schlage l lever return spring
”
RELATED FAQS
Question
Answer
What is the part number for the lever return spring for the MA lock?
Resolution:
Lever assemblies part numbers are found in the Pricebook. Note they are handed.:
What is the part number for the lever return spring for the old M series mortise lock?
Resolution:
Falcon is reintroducing the lever return spring for the discontinued Falcon M mortise series. Effective November 1, 2014 the lever return spring is now available for purchase with a list pric...:
Why does the lever on my T lock lever droop?
Resolution:
Issue: One or both levers don't stay horizontal and droop down. Facts: Falcon T series locks in a high use application. Cause: Weak or broken springs within t...:
What is the part number for the lever return spring for an old 182LE trim?
Resolution:
These parts are no longer available. For reference the spring part number is 4841 and the clip part number is 4326.:
Are parts still available for the old Falcon M locks?
Resolution:
Related solution: What is the part number for the lever return spring for the old M series mortise lock?:
What is the door-to-lever tip distance on the S Jupiter lever?
Resolution:
The lever return distance (tip of lever to door face) on the Jupiter lever design is approximately 1-3/4".:
What is the California State Reference Code regarding lever return?
Resolution:
This is in regards to the California State Reference Code, (Formerly Title 19, California State Fire Marshal Standard) stating that all levers with returns comply; levers must return to within 1/2"...:
What are the dimensions on the LAT and LON levers?
Resolution:
See dimensions for LAT and LON levers from the L9000 series :
Why does my lever sag on an L9000?
Resolution:
Levers may sag due to an incorrectly installed springcage or an incorrect springcage.Mortise locks with a fixed (rigid) lever such as an L9080 will use a spacer on the rigid lever (outside) and a s...:
What was the part number for the old D series levers spring cage?
Resolution:
The old D series springcage part numbers are as follows: C303-035 - Inside Springcage C303-036 - Outside Springcage These parts are no longer available.:
Why is the Von Duprin 55 or 88 series crossbar sagging?
Resolution:
There are a number of reasons the Von Duprin 55 or 88 series cross bar may not operate properly: The hinge case spring lifts both lever arms and the crossbar. To check spring, pu...:
I get three green blinks of the Schlage key and it says motor stall on my SUS/HHD during diagnostics?
Resolution:
Just align the triangles per the installation instructions to allow full motor movement. - This will eliminate the SUS motor STALL report. - This will eliminate the three ...:
Is the Schlage Latitude and Longitude lever available in a stainless steel finish?
Resolution:
Beginning January 2, 2013 Schlage will offer the Latitude (LAT) and Longitude (LON) levers in the 629 and 630 stainless steel finishes.:
What other locks can the blue lever removal tool 24002693 be used with?
Resolution:
On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project. This tool can be used for Schlage ND-Series ...:
How does the Von Duprin 98/99 rim or vertical rod exit device with lever trim convert from L to L-NL function?
Resolution:
To convert the Von Duprin 98/99 Rim or Vertical (Rod or Cable) Exit Device with functional lever (996L-R/V) to act like a rigid lever (996L-NL-R/V) with key over ride follow these steps: R...: