This option is not available as there is no NL cam to directly drive the rods and using a key to lift the heavy stainless, brass or bronze rods would damage the key.
The Falcon 1390 exit device is discontinued and there are no parts available any longer from the factory.
New England Door Closer may still have some older kits and can ...
Chexit devices shipped after 8-24-2015 with motor driven:
The Chexit device will use a 1 1/4" mortise cylinder with straight cam. Schlage cylinder 20-001-114 recommended.
CAUTION: The length of t...
Chexit devices shipped prior to 8-24-2015:The CX device will need a 1 1/4" mortise cylinder with a straight cam per page 2 of the installation instructions. A 996L-M for a 1 3/4...
Factory finished painted doors are available from Steelcraft. Frames "are not available" factory finished from the factory.
Doors are offered in variety of standard colors or can be fini...
Key-in-lever tailpieces differ in length depending on the lock series, function, and design. Click here to identify the tailpiece and length.
NOTE: Modular cylinders use...
Steelcraft locates all butt hinges from the top of the door to the centerline of each hinge as standard practice:
Locating hinges to the center line of the hinge keeps all hinge locations the sa...
When installing the arm; the gearbox shaft and door must be at the (+90°) full open position. The following step are used to install the Sr. Swing (REG) push arm. Install the header and door brac...
Yes, the QEL device includes a cable assembly part number 110388-00.Since 12/2014, that cable comes in a package (part 116549) with the long cable mentioned above and the small cable that plug...
Use #18 gauge wire up to 200 feet maximum distance from PS900 x 900-2Q power supply to the QEL exit device. The new QEL+ no longer requires the 900-2Q board but still needs a different option board...
Product shipped on or after Feb. 8th, 2016 The "3034" and "3034H" are internal part designation that LCN uses to specify regular (3034) and hold open (3034H) roll...
On Feb 8th, 2016 - LCN launched the redesign of the Hold open clip which
changed multiple components of our Track style closers, including the roller, track, hold open clip, and bumper.
Beginning with Firmware Packages ADFwPkg 2.16.3 and COFwPkg 1.20.0 the PIN length can be manually changed for AD200 and CO200 locks as follows:
1. Press {programming code (default is 97531)} then ...
This configuration is not possible as the anti-pick plate of a "DL" or "F" device center case interferes with the LM/DM switch mounted also on the center case.
The following items may cause the exit devices top latch from being held in the retracted position.
1. The top or bottom rods are out of adjustment.
2. The top latch hold back...
Following exit devices 2227/F, 33/3527A/F, 33/3547A/48A/F, 98/9927/F and 98/9947/48/F have similar rod adjustment procedures.
All top latches control the bottom latch assemblies. When do...
The spring in the hinge case or end case assembly lifts the crossbar and both lever arms. If broken, the crossbar and lever arms will drop down. The weight of the crossbar and levers will automati...
The new 33A/35A center case will not work with the old 33/35 series exit devices.It is never intended to use parts to convert a device from one Series to another Series as this would void the ...
To convert the Von Duprin 98/99 Rim or Vertical (Rod or Cable) Exit Device with functional lever (996L-R/V) to act like a rigid lever (996L-NL-R/V) with key over ride follow these steps:
Remove ...
The Falcon Monarch 718C and the 718NL trims can be used on the 25-C exit device.
The 718C trim is listed in the Price Book for the 25 series
The instructions attached will give dimensional i...
This is not a recommended application as the electric strike does not have the same holding force as the XP98/99 rim exit device. The electric strike has 1500 pounds of holding force whereas the XP...
Von Duprin does not recommend using XP98/99 devices with any electric strike.
Von Duprin recommends using the standard 98/99 rim device. The XP device has 2000 pound holding forc...
There is not enough room for both options as the dogging mechanism in a standard cylinder dogging and the electronics for the EL or QEL options are both located at the end of the base plate.
For 9...
The Von Duprin 6111 electric strike would work with DOM 1790 device on medium style doors
Centerline of the 1790 device mounting screws are located 1 11/16" from face of stop. See d...
Device: Pushbar end caps, pushbar trim and center case cover.
Trim: Lever assembly, trim plate assembly (trim plate and bushing sleeve).Bronze Finish Comparison
There is not a fire rated version of the Von Duprin 33A/35A rim device.
Only the vertical rod devices (33/3527A-F, 33/3547A-F, 33/3548A-F) can be fire rated.
To convert the Von Duprin 9975NL(Night Latch or Storeroom) to 9975L (Classroom) exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory):
Turn the NL ...
To convert the Von Duprin 9975L to 9975NL exit function follow these steps (Note: the mortise lock is shipped as Night Latch from the factory):
Turn the NL screw on 7500 mortise lock counter clo...
Allegion order forms are only available to Authorized Distributor Partners.
Authorized
Allegion Distributor Partners can view order forms and ordering
information by logging onto the “My All...
Position the 379L trim and attach with countersunk screw into the bottom stud of the trim.
Position the 55 Rim device and attach with the device mounting screw through the head of th...