is anti ligature trim available for thick doors

RELATED FAQS

Question
Answer
The anti-ligature trim is only available for the Schlage L-Series mortise lock and is not an option for the ND-Series.
The L9000 lock can be ordered for doors greater than 1 3/4" thick.  The allowable door thickness is dependent on the L lock function and how the lock is extended.  All locks for exte...
When dealing with glass lights in doors, there are three (3) critical dimensions which must be coordinated: Exposed Glass Size (EGS) - the horizontal and/or vertical dimensional size of the vision...
An anti-ligature lever and knob are available on the Schlage L9000 Series Mortise lock with a special recessed ADA complaint thumbturn and cylinder ring. When ordering, specify the S...
The L Series lock can fit into a door prepped for the SCHLAGE K Series with some additional prep as described here.  
K and L trim and parts are not interchangeable. 
Currently, the 914KIL trim will only work on 1 3/4" doors.
The Schlage L0170 is not available with the L escutcheon design because due to the narrow size you cannot fit the mounting plate underneath.  The mounting plate must sit on a "diamon...
Window kits are available for Steelcraft doors as either factory installed or prepared and installed by a distributor. Factory prepared light cutouts are supplied with Dezigner trim as st...
It is always recommended to point installers to the industry installation manuals which are very comprehensive and are ANSI documents. SDI (Steel Door Institute) installation manual can be found...
Doors are available with cutouts only. This practice is used for field installation of aftermarket (non-Steelcraft) glass trim by either the distributor or end user. The following information must ...
See image, ANSI A115.1 Mortise Lock PrepThis door prep requires the N escutcheon with the L283-029 spacer kit to keep the springcage from falling into the door.  Spacer kits are...
Aluminum trim is not available. All of our current trim offerings are steel.
Yes, the holes on the door would be covered up by the 25-R-L device.
The (4) center case mounting holes are in the same location but there are some small modifications that will be needed like the 3/4" dia. hole at device CL for the main cam clearance shown o...
The standard L9000 lock can be ordered for thin doors (1 3/8") and the appropriate parts will be shipped.  The LV9000, L400, LM9000, Anti-Ligature, and N escutcheon trims a...
The Schlage L9000-Series with anti-ligature trim cannot be ordered less cylinder (L cylinder suffix), but can be ordered less core (BD or J cylinder suffix). The cylinder rose dimensions change bas...
Von Duprin 98/99 and 98/99XP Rim/SVR/CVR(steel door only)/Mortise exit devices are compatible with AD200, AD250, AD300, AD400, AD401-993 exit trims.
Von Duprin 22/22F Rim/SVR exit devices are compatible with AD200 and AD250-993 exit trims.
Falcon 25 Rim exit device is compatible with AD200 and AD250-993 exit trims.
The 996L trim is the current standard trim with a break away feature built into the lever. The 994L was the original breakaway lever trim for the 98/99 series.  DISCONTINUED in mid ...
  Additional information: The 996L looks like the 992L The 996L replaced both the 994L and 992L The internal parts for the 994L and the 996L are exactly the same. The 992L prep was a li...
Dezigner Trim – This unique and patented glass trim has been designed to closely simulate trims installed in wood doors and is factory: Supplied recessed into the door face, to provide a neat f...
Flush Mounted Steel Trim for Insulated glass – Designed for 1” thick insulated glass. Recessed into the surface of the door face Accommodates 1" (25 mm) thick glass. When installed, fastener...
Overlapping Steel Trim (also refer to as conventional steel trim) – This trim is the typical glass trim supplied by most hollow metal manufacturers. Surface mounted on the door face. Accommo...
Flush Mounted Steel Trim – This trim is similar to Overlapping Steel Trim but is factory supplied recessed into the door face and is available for 1/4” glass. Glazing stops are screw attached, fast...
 Basic glass trim details:
A 1 1/4" mortise cylinder with straight cam (similar to the Schlage B502-191) or a 1 1/2" mortise cylinder with straight cam using supplied spacer collar. Cylinder length does not chan...
All Von Duprin 98 and 99 trims include screws for both 1 3/4" and 2 1/4" thick doors.
Standard mounting packages are only for a 1 3/4" thick door. Door thickness other than 1 3/4" need to be specified when ordering the device.
Torx screws are not standard on the antiligature trim but are available as an option. Specify the L283-121 Torx screw pack.  This pack includes torx screws for the armor and strike. The rest of th...
The easiest method to obtain an AL lock for a 2" door is to specify a 2" thick door when ordering.  
Part required by function:2 each A700-043 driver & A700-034** lever insert in addition to the chassis parts below:AL10S – 2 hubs A700-028AL25D – 2 hubs 1 A700-028 (inside), 1 A700-030 (outside)...