is an L lock rehandable

RELATED FAQS

Question
Answer
Beginning January 2, 2013 Schlage will offer the Latitude (LAT) and Longitude (LON) levers in the 629 and 630 stainless steel finishes.
The finishes below are available on the L9000, some lever designs and trims are not available in all finishes.  605  Bright Brass  606  Satin Brass  609 &...
Reference the L-Series Service Manual to change lock functions or build up a case from parts.
This Step-by-Step guide is specifically designed for the functions listed below, however, it can be referenced with a majority of L series functions since most of the parts are ...
The lever removal tool can be used to remove levers in both the ND and the L Series mortise locks.
On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project.  This tool can be used for Schlage ND-Series ...
Inside knob and bushing: 09-402 plus design and finishOutside knob: 09-401 plus design and finish
In late July, 2014, Schlage began taking orders for a new high visibility indicator for both N escutcheon and sectional trim applications.  A complete listing of lock functions and part number...
The L Series mortise indicator datasheet can be found here. Includes how to order.
The square block is probably the springcage assembly, L283-040.  This component has an internal spring to keep the lever in the horizontal position.
The part number is K110-020 (includes 2 screws).  You will also need to specify the finish.
The following steps are required to convert the Von Duprin 98/9975L from classroom to night latch function: Order new 996L-NL-M trim and reset NL drive screw in mortise lockbody as set from...
Applies to L9090EL/EU, L9091EL/EU, L9092EL/EU, L9093EL/EU, L9094EL/EU, L9095EL/EUOvervoltage will cause the lock to shut down for approximately 5 minutes to allow the circu...
To order less complete trim one side use LLL as the designation for less complete trim outside or inside. This applies to the L9000 & LM9300 Series mortise locks. LESS OUTSIDE TRIM Examp...
Cleaning and caring for the lock will vary depending on the finish. Clear-coated or oil rubbed finishes can be cleaned periodically with a mild non-abrasive soap and buffed lightly with a clean ...
Applies to L9090EL/EU, L9091EL/EU, L9092EL/EU, L9093EL/EU, L9094EL/EU, L9095EL/EUThese models require 12/24 VDC with a peak current of 0.4 amps.  The following po...
Applies to L9080EL/EU, L9082EL/EU (Discontinued)The Schlage L9080 EU/EL and L9082 EU/EL require 24 VAC/VDC with a peak current of 1.3 Amps at 5 to 10 second intervals and a holding curren...
The L9000 lock can be ordered for doors greater than 1 3/4" thick.  The allowable door thickness is dependent on the L lock function and how the lock is extended.  All locks for exte...
Applies to L9090EL/EU, L9091EL/EU, L9092EL/EU, L9093EL/EU, L9094EL/EU, L9095EL/EUThe Schlage electrified L-Series wiring diagram can be found here and the re...
Applies to L9080EL/EU. L9082EL/EU (Discontinued)The Schlage electrified L-Series wiring diagram can be found here and the requirements are listed below. 24VAC or 24VDC (maximum 26V, ...
Click here to show the differences of an installed lockcase between the L9090, L9091, L9092, L9093, L9094, L9095 EL/EU and the L9080 EL/EU
RX wiring on all L9000 locks with RX switch manufactured after January 2, 2017:The L-Series switched to a handed modular three-wire request to exit (RX) switch. This change was originally completed...
Specific to the RX switch installed into the L9080EL/EU and L9082EL/EU and L9000 mechanical locks prior to January 2, 2017:ALL PART NUMBERS BELOW DISCONTINUEDThe L-Series switched to a three-wire r...