FAlcon Cylinder Tools

RELATED FAQS

Question
Answer
A double cylinder(-2) option is not available on a Falcon device but is available from Von Duprin.
It is not possible to key SFIC and standard cylinders including Schlage FSIC into the same system.  A keyway name may be shared between the two key fami...
Schlage does not have a stainless steel/non-ferrous lock series. The only option that Allegion provides is the Grade 1 cylindrical Falcon X-Series. To order the Falcon X with the stainless st...
The Falcon W replaced the Z lock in July 2006.  The Z lock was a cylindrical chassis.
The Falcon Monarch 510L and 510L-NL trim will accept either a 1 1/4" Mortise cylinder with a straight cam or a 1 3/8" Mortise cylinder with a straight cam using the blocking ring provided with the ...
Von Duprin does not supply cylinders keyed alike.   Cylinders keyed alike are available from Schlage and Falcon.
The Exit Alarm takes a 1 1/8" Mortise cylinder with a straight cam. See first page of Exit Alarm inst below. Exit Alarm inst
Schlage and Falcon double cylinder deadbolts have concealed screws to prevent tampering. The two methods used to conceal the thru-bolts are using screw caps or a faceplate. Use the below instructio...
Schlage and Falcon use the P cylinder suffix to designate conventional key-in-lever (KIL) 6 pin cylinder.  The D means that the lock will have a deadlatch.
The thread spec on Schlage and Falcon mortise cylinders is 1.150 x 32
Conventional Cylinders - A conventional cylinder is one that requires some breakdown of the lock in order to be removed. These are the most commonly used cylinders sometimes called key-in-lever...
The following document contains information on Falcon (Non I/C) Hotel Cylinders, including part numbers, key requirements and operation. Falcon Hotel Cylinders.
The current tools, pinning kits and key originating machines for all Schlage Everest full size cylinders and small format cores are the same used on Everest 29.
Key in lever Falcon cylinders do not work in Schlage locks.  The cylinders may fit, but there are no specific tailpieces created to operate any Schlage lock. SFIC SFIC is universal so Falcon and...
   Hotel cylinder in L9000 As long as the correct cam is used (Schlage clover), a Falcon Hotel cylinder will properly function in an L9486 hotel lock.
Order the M204-198 thru-bolt jig, see Figure 1. Figure 1: M204-198 thru bolt jig The 40-080 was the old Schlage jig. The 030736-000-70 was the old Falcon jig.  When the jig changed to...
All lock cylinders on a specific project are operable by a special "project key".  Duplicates of this key may be assigned by the building contractor to workmen and subcontractors as required. ...
The Falcon MA-Series requires a different cam for keyed functions than its predecessor the Falcon M-Series.
 
 
AL-Series and discontinued D Lever-Series locks use castle nuts to hold the chassis to the spring cages and to keep the chassis positioned in the door. This causes confusion at times when the lock ...
Falcon D series deadbolts will not accept Schlage Key-in-lever cylinders. The faceplate plug hole is smaller in diameter than the Schlage plug and does not fit flush when i...
For a Schlage "C"  keyway:  Specify "CP6" as the cylinder suffix when ordering  D100 or D200 locks (All other Schlage keyways are not available).
Pricing information is not a part of the Knowledge Center data. For all hollow metal price comparisons please e-mail the Steelcraft Estimating Team. For your reference, the e-mail address...
The cam is not inverted on the mortise cylinder for the CD option.
The Falcon C987 cylinder can be ordered with the #27 cam as it has a similar profile to the Schlage B520-731 cam for trims after 2/28/2011.
 See the attached Technical Note for instructions on saving a "Device Template" FROM a device or loading TO a device, Device Template Tech NoteOn the SUS/HHD go to the LOCK Properties tab, and sele...
Devices built After 2/28/2011: Use a 1 1/8" - 1 1/4" mortise cylinder with straight narrow cam. (Cam profile same as the Schlage B520-731, see table below for part numbers) Devices built Befo...
 Modular 1-1/8"  Modular 1-1/4"  SFIC and FSIC  Non-Modular Non-IC Conventional  Non-Modular Non-IC Everest Primus  B520-730  B520-731  B520-2...
Unless otherwise specified on an order, the cam supplied on Falcon mortise cylinders will be the following: Non-IC mortise cylinder is the 5622-STD. IC mortise cylinder is the 5622-IC. Related...
Cams for other applications may be specified with no additional charge, see pricebook.
The blue lever tool remover, 24002693, is not shipped in every box. The existing wire spring lever removal tool will be included in every box.  
Falcon Standard Bitting Specs - 018 system Falcon Restricted Bitting Specs - 025 system
Used for installing interchangeable core housings.
See attachment that describes this tool.
For standard (non-IC) cylinders, use the Falcon #4 straight cam For IC cylinders, use the Falcon #5 cam 
Schlage offers Falcon Retrofit cylinders to fit many of Falcon's locks.  Table 1 below contains part number for T series locks.  Table 1 - Falcon retrofit cylinders  
The B520-698 cam was designed for a Schlage IC mortise cylinder (see Figure 1) to operate a Falcon MA lock, all functions except the MA381.  There is no Schlage cylinder option ...
Only the lever return spring is available.
Related solution: What is the part number for the lever return spring for the old M series mortise lock?
The standard cylinder keyway that comes with the 914KIL trim is a Schlage 6 pin "C" section.
Schlage Everest 29 is a new keyway family that launched in August 2012 and is patented until 2029. It offers the highest level of restricted key system security by Schlage through patent protection...
The emergency keys are shipped with each lock.  The part numbers are; 61-509 standard and 61-510 large bow size.
The "C" indicates small format IC core, which is the only core style Falcon products.  The C987 will be provided less core unless -6, or -7 suffix is specified (6 or 7 pin core) Example:...
This option is not available as the solenoid is in the mechanism case where the dogging components would go.  An HD-EL solenoid is not available, and Special Dogging(SD) is not an option ...
The Monarch KIL trim uses the following cylinders: Schlage Cylinders 23-013 Conventional 20-750 Primus 20-750-XP Primus XP 20-550 Primus UL437 20-550-XP Primus UL437 XP Falcon Cylinder A23165-0...
The lever removal tool can be used to remove levers in both the ND and the L Series mortise locks.
On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project.  This tool can be used for Schlage ND-Series ...
Schlage now offers modular style cams to operate the Falcon MA locks.  The following part numbers are cams for all MA locks (except the MA381): L583-638 for 1-1/8", 1-3/8", 1-5/8" length cylin...
Price Book 72A List Price $8.10
Cylinder Dogging(CD) is not an option on any Falcon-Dor-o-matic device.
The following application information apply to the 5100 electric strike: Can only be used on a single door with a cylindrical lock Can not be used on a pair of doors Can not be used on a mullion