Schlage

Question
Answer
According to ANSI specifications for cylindrical or mortise locks: The lock strike centerline should be 40 5/16" from the bottom of the frame with the lock in relation to the strike. &...
The door handing determines the finish of the latch and strike. Left reverse and right reverse doors default to outside trim Left and right hand doors default to inside trim If lever an...
See letter excerpt below.  Parts are no longer available.Effective June 30, 2000 Schlage Commercial is announcing the obsolescence of the ME-Series and ULTIMA 505 bright brass finish option fo...
The ME trim was discontinued in 2001 and no longer available.
Schlage does not have a stainless steel/non-ferrous lock series. The only option that Allegion provides is the Grade 1 cylindrical Falcon X-Series. To order the Falcon X with the stainless st...
The Schlage B60 is a residential grade 1 deadbolt and is not available with Everest or Primus cylinders.  If Everest or Primus is needed then a commercial deadbolt will have to be used - eithe...
Cylindrical and Tubular Style  Grade 1: 800k Grade 2: 400k Grade 3: 200k  
Mortise Grade 1: 1 Million
J lock was an old Residential product no longer supported -
The L Series lock can fit into a door prepped for the SCHLAGE K Series with some additional prep as described here.  
K and L trim and parts are not interchangeable. 
  Schlage H-Series Escutcheons    Part Number  Description Dimension   07-057  Inside escutcheon and turn  6.92" x 2.75"  07-035  Inside escutcheon, dummy - H170  6.92" x 2...
At one time we offered a 9453 function in several different lever, knob and grip handleset designs. A wide variety of trim offerings were available. The mortise lockcase was a smaller version of th...
Click on the applicable Schlage G Series link below for template information. Wood Template 1 1/8" x 4 1/4" Radius Wood Template 1 1/8" x 4 1/4" Square Wood Template 1 1/4" x 8"Metal Templ...
L9066 x XL11-897 Storeroom Lock  Key in either cylinder locks or unlocks both levers. When locked, latchbolt retracted by key either side. Specify per XL11-897 with the lock function when or...
There are several Schlage and/or Falcon locks that have been tested and approved for this application. For Commercial use the locks have been tested and approved as assemblies wit...
1) General Lock was purchased by Schlage - 1973 2) General Lock moved to Security and turned into the K-lock - 1977 3) K-Lock discontinued - approximately 1984 4) L-lock introduced - approxim...
Lubriplate is a grease that can be used for our locks and is available in the price book for purchase, M204-168.
In early 2013 the ND85 plunger assembly was improved to prevent accidental rotation of the inside button.  The previous design could allow someone to unintentionally rotate the button and unknowing...
BAA/ARRA stand for Buy American Act and American Recovery and Reinvestment Act. A brief description of some of the federal requirements can be found in the BAA Catalog on the Allegion...
Country of Origin (COO) information can be found in the Buy American Act (BAA) brochure.
To obtain product certification forms:Download the BAA Catalog on the Allegion website Complete the information requested in the the BAA Catalog with a detailed copy of the prod...
The Schlage ND electrified locks can be ordered with a 3-3/4" backset, but the latch cannot be ordered separately because of UL regulations.
The Schlage L-Series uses a clover leaf cam with the exception of the L9060 outside cylinder which uses a straight cam. The cam part number will depend on the type of mortise cylinder, keyway (for ...
Putting a standard non-hotel cylinder in a L9485 or L9486 will change the operation of the lock to the L9480, storeroom lock with deadbolt.
1 1/8" mortise cylinders fit the 650 series keyswitch.  The 650 series keyswitch when ordered with the cylinder, will come complete with the correct cylinder, cam, and any required blocki...
If blocking rings (PN 36-079) are needed, specify dimensions when ordering. See below for blocking ring (PN 36-079) dimensions.  Blocking Ring  Specify Dimension  1//8" ...
Typical installation by an experienced Schlage L lock installer on a door correctly prepped for the Schlage L-Series function could take 10 to 20 minutes.  Many outside variables can change the amo...
ND53PD (ANSI F109) Entrance Lock  Turn/push-button locking; pushing and turning button locks outside lever, requiring use of key until button is manually unlocked. Push-button locking; pushing bu...
Medeco does offer a key-in-lever cylinder to fit the Schlage ND.You will need to contact Medeco for the cylinderSpecify a key-in-lever cylinder to fit the Schlage ND lock.They will supply a cylinde...
Lip length refers to the dimension from the centerline of the strike screw holes to the edge of the lip.  See the attached as lip length depends on door handing and thickness, Extended Lip Str...
Authentic oil rubbed bronze finish, or finish code 613 oil rubbed bronze will wear over time due to the “rubbed” finishing method which does not allow application of a protective coating or plating...
The Schlage G-series lock came with two types of conventional core cylinders. One was a non-removable cylinder and the other was a removable (demountable/interchangeable core) cylinder that looked ...
As of September 8, 2017, Fusion Hardware will cease operations and no longer be accepting new orders. For questions or concerns with orders and shipments:Contact: Fusion Customer Service ...
Fusion Hardware has been a brand of Allegion since 2010.  Fusion offers an extensive collection of door hardware that can be integrated into a vast array of rooms, homes and spaces. Custom-des...
Supported Devices AD Series Locks AD-200                          ...
The 38-075 was a spring cage retrofit kit used on the old D series locks manufactured prior to October 1994.  Kits contained 2 each spring cages, 2 each roses, 2 each mounting screws.
The minimum clear opening width for ADA is 32" measured from face of door opened to 90 degrees to face of stop on strike jamb. There must be no hardware mounted to the door projectin...
The only Schlage lock with a toggle was the discontinued K-Series mortise lock.
Two change or user keys are supplied with each lock.
AL-Series and discontinued D Lever-Series locks use castle nuts to hold the chassis to the spring cages and to keep the chassis positioned in the door. This causes confusion at times when the lock ...
Schlage offers the AL170 single dummy trim, but for applications where a double dummy is needed you can install two AL170 dummy trims back-to-back.  Each AL170 is shipped with a threaded rod (part ...
Schlage offers a comparable cam to the Yale 2160 and it will operate any Yale lock that utilizes the Yale 2160 cam.     Schlage Cams for Yale 2160  Part Number  Description  B520-7...
The Schlage L0170 is not available with the L escutcheon design because due to the narrow size you cannot fit the mounting plate underneath.  The mounting plate must sit on a "diamon...
When ordering dogging with cylinder; specify complete cylinder with appropriate option below:XQ11-949 for all conventional cylinders  XQ11-948 for full size and small format IC cylinders
XQ11-947 was used Classic conventional cylinders prior to the release of modular - NOW OBSOLETE
Schlage does offer rabbetted latch and strike kit: Part number, 39-030, for cylindrical locks and deadbolts.  Part number, 10-075, for the L9000 mortise locks. Monarch does not offer rabbette...
ND50PD (ANSI F82) Entrance/Office Lock  Push-button locking. Push-button locks outside lever until unlocked with key or by turning inside lever. Inside lever is always free for immediate egress. ...
The BHMA standard 689 is an Aluminum finish, and is silver/gray in color.
Order the L283-146 XL11-543 for each L9482 lock body needed. 
The blank inside plate for the B661/761/861 is part number 12-626.
Yes. Both Schlage and Falcon SFIC mortise housings will accept 6 and 7 pin cores with no additional parts.
Uncombinated cores are furnished less keys, pins and springs.  Ordering the 80-036 will get you an empty core so you can key it.
The MD latches are no longer available.  A picture is below.
BHMA provides a certified products directory complete with function codes and meanings from most of the major lock manufacturers.  The most up-to-date directory can be accessed through th...
The D lever was discontinued in October 2003 and there are no parts available.
Deadbolt operated by key from outside or by turn unit from inside. Bolt automatically deadlocks when fully thrown. Latch retracted by lever from either side. Turning inside lever retracts deadbolt ...
The L9453 mortise lock case part number is L283-137.
RX switch is request exit and LX switch is latch bolt monitor switch. They do not required a power supply directly. The electrified hardware that RX or LX switch conne...
UL 437 is an Underwriter Laboratories label and is their Standard of Safety for Key Locks.
The ND70 X 80 operation can be reversed to allow keyed latch retraction on the outside and lever locking and unlocking on the inside. To do this correctly and maintain the security of the...
L9050 LV9050 (ANSI F04) Entrance/Office Lock  Latchbolt retracted by knob/lever from either side unless outside is made inoperative by key outside or by turning inside thumbturn. When outside is l...
D73PD or ND73PD (ANSI F90) Corridor Lock  Locked or unlocked by key from outside. Push-button locking from inside. Turning inside knob/lever or closing door releases button.
Schlage does not test their locks for ballistics or bullet resistance.
Depending on the application, there are two types of blocking rings offered - One for use with a compression ring, and one for use without.  When a compression ring is used, it's diameter is l...
After selecting the correct blocking ring, specify the thickness.  The table below shows the different thicknesses that the rings are offered in.   
Schlage and Falcon use the P cylinder suffix to designate conventional key-in-lever (KIL) 6 pin cylinder.  The D means that the lock will have a deadlatch.
Click here for the Schlage Modular Cylinder Marketing Sell Sheet for information on the modular cylinder.
These items are not available from Schlage or Falcon. There are third party companies such as Don-Jo or Pro-Lok that manufacture cover plates.
There is no direct replacement.  This deadbolt was the standard bolt provided for the BC100-Series which was discontinued in 2007.
ND93PD (ANSI F88) Vestibule LockLatch retracted by key from outside when outside lever is disengaged by key in inside lever. Inside lever is always unlocked.  ND95PD (ANSI F110) Classroom Securit...
The Schlage L-Series mortise lock spindle and spring part number can be found in the Table 1.     Spindles and Springs   Part Number  Description  L283-060 Spindle and spring, 1...
When synchronizing door files to the HHD  ensure that the SUS is not running.Make certain the proper sync folder location is properly configured in the Schlage express softwareVerify cable pro...
The replacement solenoid for the Schlage L-Series mortise lock is part number L283-053.
Only the 10-079 or 10-078 strike should be used with the L400-Series.  
The storeroom lock function is described as follows: Latch bolt operated by key from outside or by operating inside lever. Outside lever is always inoperative. The following are storeroom functi...
The minimum stile for each lock will depend on the backset and the rose diameter/escutcheon width.  See the Schlage Minimum Stile Guidelines  for the minimum stile for each...
40-070 is the part number for the Primus pinning kit. 
AutoCAD drawings are proprietary and are not available for distribution.  One option are BIM objects which are available.Allegion now has BIM objects available for the LCN®, Schlage®, Ste...
B600-092 is the inside snap-on faceplate for all non-IC double cylinder B562 and B662/762/862 deadbolts.
The 23-065 is the conventional cylinder for the ND-Series lever.
You can set a timezone for a user but not an auto-unlock on the BE367
Outside Knob/Lever and Rose/Escutcheon Assemblies      Part Number  Description    A Rose with Knob/Lever  09-506  Designs: 01 02 03 05 06 07 12 17 18 OME 41 42     09-655  Des...
The 81 service manual can be found here.
Purchase the L9080 lock case (part number L283-134), switch it with the L9070 case and use the existing trim.
The full size interchangeable cores or FSIC from Schlage.
L9071 LV9071 (ANSI F32) Classroom Security Lock  Latchbolt retracted by knob/lever from either side unless outside is locked by key from either side. Auxiliary latch deadlocks latchbolt when door...
L283-263 and L283-239 are obsolete part numbers that were used to specify "request to exit" on the L9000 and LV9000 locks. To specify RX on L9000 locks after January 2, 2017, specify the lette...
Z-Wave® is a mesh networking technology developed in 1999 to create a standard for wireless radio frequency (RF) communication for home devices. The key to the technology is that Z-Wave products ar...
Swapping out the following parts of an ND50 will convert it to an ND53: Swap N123-028 Push button plunger for  N123-017, Push and Turn button plunger Swap N523-000, Push button for N523-001 Pus...
e.Primus was an electronic lock system that used iButton credentials to unlock a door.  Product was discontinued in July of 2002 with parts were available only for a short time.  Product support fo...
03-042 is the part number for the inside or outside rose.
ND -series locks manufactured on or after January 30, 2017 use the following spring cages:Outside - N523-218 - For ALL cylinder options except for JD-YA6, JD-YA7 and JD-MEDInside - N523-222 -...
ND-series locks manufactured before January 30, 2017 used the following spring cages:
Click here for a list of available Schlage cams comparable to the Sargent 13-0660.
The 80-033 will fit in an AL lock, but will be supplied uncombinated. Pins and springs are not supplied.
To convert a Schlage mortise L9080 function to a L9070 function purchase and replace the following:   L283-133, L9070 lock case  L283-040, spring cage (for outside lever)
 Mounting Posts   Part Number  Door Thickness  L583-211  1 3/8"  L583-212  1 3/4" - See note section on SL1 trim  L583-213  2...
20-059 is the standard straight cam FSIC housing only used with Von Duprin, Monarch, and other straight cam applications. 30-032 is the straight cam FSIC housing only for the outside of the Schl...
The Schlage small format interchangeable core rim cylinders 80-329, 80-159, 80-116, and 08-129 can accept 6 pin and 7 pin small format cores.
HD /SUS  must be in serial communication mode. Tap icon at right of the  banner " no device connected". It should show the image of a 9 pin D connector for serial communication.once this ...
L9040 locks WITHOUT indicator uses an emergency tool available in the price book, L583-233.L9040 locks WITH an indicator requires a small flat blade screwdriver.
To install a Schlage ND170 click here for the installation instructions.
The old D series springcage part numbers are as follows: C303-035 - Inside Springcage C303-036 - Outside Springcage These parts are no longer available.
The Flair design handing must be specified when ordering a complete lock or just the lever.
The Schlage B and BD cylinder suffixes designate less small format interchangeable core (SFIC) cylinder prep for the lock. Any SFIC, 6-pin or 7-pin, can be inserted into the lock and will operate t...
L583-446; Schlage Adams Rite MS modular cam used on 1 1/8", 1 3/8" and 1 5/8" cylinders    L583-447; Schlage Adams Rite MS modular cam used on 1 1/4", 1 1/2" and 1 3/4" cylinders  B502-944; Sch...
To convert the AL44 to an AL40 you can replace the outside plunger unit in the chassis or order the AL40 chassis.  Replacing the plunger unit is more difficult and time consuming and would not be r...
Backset is the horizontal distance from the face of the lock (door edge) to the centerline of the knob hub keyhole or cylinder. 
ND85PD (ANSI F93) Faculty Restroom Lock  Outside lever fixed. Entrance by key only. Push-button in inside lever activates visual “occupancy” indicator, allowing only emergency master key to opera...
CLASSROOM LOCK: A lock that locks and unlocks the outside lever with a key.  Inside is always free egress. ENTRY LOCK:  A lock that locks and unlocks the outside lever with button/turn on the insi...
ND66PD (ANSI F91) Store Lock  Key in either lever locks or unlocks both levers. Key in either lever locks or unlocks both levers.
The 40-025 was replaced by the 40-176 multi-spur bit.
The B220-001 is an FSIC rim tailpiece and driver.
A 626 or US26D.  Schlage definition of the 626 is a satin chromium plated finish.
Refer to table 1 for the list of Schlage AL-Series cylinders.     AL-Series Cylinder Reference Table    Function  Cylinder Mechanism   Complete Cylinder   Non-Hotel Functions  ...
The commercial Aged Bronze finish (643e) is the BHMA equivalent to a copper plated, blackened, relieved and then clear coated product. This commercial finish is identical to the residential Aged Br...
In late July, 2014, Schlage began taking orders for a new high visibility indicator for both N escutcheon and sectional trim applications.  A complete listing of lock functions and part number...
The L Series mortise indicator datasheet can be found here. Includes how to order.
The Schlage B400 deadbolt was a grade 2 deadbolt and was discontinued April 1, 1996.  Its replacement was the B100 grade 2 deadbolt and no parts were compatible between the two.
Functionally equivalent to a schlage 350+ which is functionally equivalent to a M450
ANSI F84 Classroom Lock  Outside lever locked and unlocked by key. Inside lever always unlocked for immediate egress.   ANSI F86 Storeroom Lock  Outside lever fixed. Entra...
To remove the Schlage L Series from a door reference the appropriate installation instructions found here at https://us.allegion.com/en/home.html
The part number for a Schlage mortise cylinder blocking ring for use without compression ring is the 36-079 (specify dimension and finish).
The UBC (Uniform Building Code) was a regional legacy building code which was superseded in most jurisdictions by the IBC (International Building Code). There may be some areas of the country which...
The Security Colorado plant is ISO 9001, 14001, and 18001 certified. Certifications listed below.ISO 9001ISO 14001ISO 18001
Information for CISA locks, cylinders and hardware is not available in Knowledge Center. For all information, please go to Allegion's CISA home page for all information.
Changing the handing of an L9000 or LV9000 lock depends on the date of manufacture.After May 31, 2019The handing screws on the L and LV chassis are now both installed facing the inside of the doorT...
Finish is not specifically stated as being covered under warranty as it is covered under defects in material and workmanship.  EXCEPTION: There is no finish warranty for Falcon products. ...
Falcon lock warranty statementIves warranty statementGlynn-Johnson warranty statementLCN closer warranty statementSchlage warranty statementSteelcraft warranty statementVon Duprin warranty statement
Schlage does not make profile cylinders. Allegion's CISA makes profile cylinders. Contact Allegion UK at http://www.allegion.com/uk
All extended warranty requests are handled by Allegion Warranty Service Team.  Email Requests to warranty.service.requests@allegion.com.   
To convert a L9080EL/EU to a L9082EL/EU you will have to remove and replace the L9080EL/EU lock case and two spindles with the L9082EL/EU lock case and the spindle. See below for part numbers (choo...
The 5100 electric strikes are for use with cylindrical locks only.  Instead use the following:6211 electric strike is used with mortise lock without deadbolt on a new single door, hollow ...
Two ND170's can be mounted back to back as a double dummy set by using the threaded rod, N523-105.  This threaded rod must be ordered separately. 
To assemble, connect the threaded rod between both springcages (H) and spin springcages in opposite directions.   
Schlage and Falcon do not offer products that have been evaluated by European Directives (CE).
Part number 80-037 is the combinated Schlage Everest small format interchangeable core and is available in the restricted Everest B Family keyways. Part number 80-036 is an uncombinated version.
To convert a Schlage ND80 to a ND70 you can replace the keycam or chassis and use your existing trim. Ordering Instructions: Keycam only: N123-010 Chassis and springcages: ND70LD LLL 626 LL...
To specify the RX option with electrified (after October 2014) and non-electrified L9000 locks (after January 02, 2017), use the designation "RX" with the lock part number.  Ex. L9050P 02A 626...
Prior to January 02, 2017:  2010 to January 2017:  The RX designation changed to L283-263 for L9000 (non-vandlgard - L9010/50/70/71/76/77/80/56/60 and the L9453/56/57/85) and&nb...
In order to change functions between an L9050 and an L9056 a new lock body would be needed.  The lock body part number for an L9050 is L283-133.The lock body part number for an L9056 is L283-1...
For all Schlage and Falcon small format interchangeable cores shipped from the factory 0-bitted, the control key will be cut to all 4's.
The B250 Night Latch is a single cylinder deadlocking latchbolt where the latch is retracted by a key from the outside or by the inside thumbturn. Rotating the thumbturn and activating the hol...
ND82PD (ANSI F87) Institution Lock  Both levers fixed. Entrance by key in either lever.
 Tailpieces    Description  Part Number  Door Thickness  B562P (Classic Non-Modular)  B600-045   1 3/8" - 1 3/4"     B600-046  >1 3/4" - 2 1/4"  B562P (Everest/Primus, Class...
A set-up key is a key used to hold the check-pin in an Everest cylinder during pinning.
Both adaptors are used on the B250 Series for doors prepped with a 2-1/8" bored hole instead of the 1-1/2" bored hole. 38-031 is a light gauge ring for use under a cylinder, diameter is 2 1/2" ...
Please contact Pro-Lok for service and warranty related questions.  They will need the serial number of the machine and the type of keyway being cut. 655 North Hariton StreetOra...
PRO-LOK warranties both new machines and repaired machined for a period of 90 days and will repair or replace (at PRO-LOK’s discretion) any part of the key machine which proves defective in the ori...
Schlage does not offer any construction keying option for a cylinder with the Primus feature, sidebar mechanism. Standard Primus cylinders: Conventional cylinders will have to be purchased and...
Per NFPA (National Fire Protection Association) 80 section 6.3.1.7 the door to jamb gap should be 1/8" +/- 1/16".
The ND25 is an exit lock with no outside trim. The inside lever is always free for immediate egress.
Rim cylinder housing only for FSIC is part number 20-079.
Rim cylinder housing only for SFIC is part number 80-129.
Schlage Everest 29 is a new keyway family that launched in August 2012 and is patented until 2029. It offers the highest level of restricted key system security by Schlage through patent protection...
The B580 "Door Bolt" is a deadbolt that is thrown or retracted by the inside turn unit only. There is no outside trim or keyed cylinder.
An open back strike is a strike with no back for use on double doors with no coordinator.  See article on idighardware.com
On August 15, 2012 Schlage began shipping ND-Series locks with a hassle free clip to aid with the installation of the anti-rotation plate.  This feature has been added to the hub to keep the anti-r...
The lever removal tool can be used to remove levers in both the ND and the L Series mortise locks.
On August 15, 2012 Schlage began shipping a new, more ergonomic, lever removal tool to coincide with Phase 1 of the ND-Series improvement project.  This tool can be used for Schlage ND-Series ...
ND locks shipping on or after January 30, 2017 no longer require the use of the soft durometer spacer. Lever installation on the redesigned ND locks should not be difficult.
For ND locks shipping prior to January 30, 2017, the addition of the soft durometer spacer (SDS) on August 15, 2012 did affect the installation of the lever.  Ultimately, removing th...
Schlage offers professional lock training both at the factory and in the field.  Years of customer observation and feedback during training sessions is that when the anti-rotation plate is installe...
The blue lever tool remover, 24002693, is not shipped in every box. The existing wire spring lever removal tool will be included in every box.  
ND locks shipping on or after January 30, 2017 will look very similar when assembled to their predecessor that shipped prior to that date. There are several ways to distinguish the old versus the n...
The Schlage Vandlgard option available on select L-Series (LV9000) and ND-Series is ideal for areas subject to abuse or anywhere vandalism is likely to be present, such as schools, universitie...
Vandlgard is specified by "LV" for mortise locks.Vandlgard is specified by ND9x functions for ND cylindrical locks.
A lock is any device which prevents access or use by requiring special knowledge or equipment. Mechanical locks are mechanical devices which secure an opening by keeping a door closed until a relea...
Tubular Locks: Tubular locks have a center spindle assembly that extends through the center of the lock body and latch, allowing for retraction of the latch when the lever or knob are rotated....
Cylindrical Locks: a bored lockset whose latch or bolt locking mechanism is contained in the portion installed through the cross-bore Medium, high to extra heavy duty Commercial, multi-family a...
Mortise Locks: a lockset where the case is designed to fit in a mortise in the edge of a door Medium, high to extra heavy duty Commercial, multi-family and institutional applications Pros - ...
Deadbolt Locks (Deadlocks): a lock with a bolt which requires a deliberate action to extend and which resists end pressure in the unlocking direction when fully extended Medium, high to extra he...
Padlocks: a detachable and portable lock with a shackle which locks into its case.   Schlage Commercial padlocks ·         KS-Series (Meets or excee...
DATE and TIME Facts – KC2-Deadbolt, BE-367, PED-500, PED-1000: • The deadbolt clock circuitry directly uses the battery as its power source. If the deadbolt battery is removed, the clock can keep...
The Schlage full size interchangeable core (FSIC) prepped B560F, B561F, and B563F deadbolts all require a UL fire cup (R) in order to be UL listed.  This fire cup is s...
SCHLAGE locks are available with the following backsets: Lock Series Lock Type                 ...
Grade 1 locks are tested and certified to be in compliance with the following ANSI/BHMA Standards: Cylindrical, Bored and Preassembled Locks & Latches 800,000 Certified Cycles ANSI/...
Grade 2 locks are tested and certified to be in compliance with the following ANSI/BHMA Standards: Cylindrical, Bored and Preassembled Locks & Latches 400,000 Certified Cycles ANSI...
Interconnected Locks: a lockset whose trim provides a means of simultaneous retraction of two or more bolts which may also be operated independently Medium duty Commercial, government or multi-...
Conventional Cylinders - A conventional cylinder is one that requires some breakdown of the lock in order to be removed. These are the most commonly used cylinders sometimes called key-in-lever...
Beginning January 2, 2013 Schlage will offer the Latitude (LAT) and Longitude (LON) levers in the 629 and 630 stainless steel finishes.
The C123 keyway is not available in SFIC. The SFIC is available is only in B Everest keyway or an R Everest 29 keyway.
Schlage does not offer electric latch retraction with any mechanical, electrified, or electronic lock. 
  Part Number Level  Classic Primus 40-061 1  40-065 1 Plus  40-062 2  Classic Primus XP 40-061-XP 1 40-065-XP 1 Plus  40-062-XP 2 Everest Primus 40-06...
Wiring and Riser diagrams can be accessed at:Common wiring diagrams can be accessed at:  http://kc.allegion.com/.   Click on the "Common Wiring Diagram" link.To request a custom wiri...
Support for the E-Bolt was discontinued in 2007.
The Schlage SL1 ligature resistant lever is designed to break-away between 100 and 200 inch-pounds.  The lever will rotate at this point but not allow access.
 The Schlage ND75 and ND95 locks require the chassis to be assembled and timed correctly for operation.  If the chassis has to be disassembled for any reason please refer to the Assembling Schlage ...
The 643e is a powder coat finish equivalent to the US11 aged bronze finish.  The 613 is oxidized and oil rubbed and is equivalent to the US10B.
Close up of the copper relieved edges on 643e
MultiPoint locks are three-point locking systems that secure the door at three points – top, bottom, and traditional center latch location. Operating just like traditional locks, MultiPoint locks a...
The old D-Series Lever used a standard lever insert similar to the pre-2002 AL-Series standard lever insert.  The old D Lever insert was smaller than the AL and the two were not comp...
Conversion kits are available to convert many popular functions.Conversion kits manufactured on or after January 30, 2017 will have the new enhanced ND spring cage, lever, plunger and buttonCo...
For all available ND Series Conversion Kit part numbers, click here.
Due to ligature guidelines you cannot "mix and match" ligature trim with standard trim.You can pair an SL1 lever with an SK1 kob.  Specify both XL11-000 & XL12-482 in the comments section ...
The P keyway is a special keyway that can be operated by C, CE, E, EF, F, FG, and G keys.
Cylinders can be ordered with the P keyway, but P key blanks are not available.
The ND80 EU is electrified bilaterally, therefore the lever should operate in both directions when the solenoid is energized. 
Key cutting shims are now available to assist with cutting ALL Everest 29 keyways. Please see the shim introduction document here. This document illustrates how the key cutting shim fits into ...
If you continue to have issues when cutting Everest keys, the following are recommended:Slowing down the feed rate.Replace cutting wheel if it is older or has a low teeth count.Use proper clamping ...
Warranty Statement3 Year Limited Mechanical Warranty and 1-Year Limited Electromechanical Warranty - Additional warranties listed below The provisions of these limited warranties do not apply to P...
Schlage and Von Duprin introduced the new M Collection of decorative levers in January 2014.Click here to visit the new webpage.
Changing the plunger assembly on the AL-Series requires disassembling the chassis.  Refer to Plunger Assembly Instructions for guidance.
You can view and subscribe to the channels below. LCN  Schlage  Steelcraft  VonDuprin  Falcon
The B571 / D271 indicator deadbolt is a Grade 2 privacy deadbolt with indicator designed to be opened with an emergency key.
The Schlage B562 double cylinder deadbolt is not UL listed.  If a double cylinder deadbolt is needed with a 3 hour UL listing, then the Schlage B662 can be used instead of the B562.
Contact you local authorized Allegion Distributor for all Allegion brand logo information.
Please visit the Schlage Residential website (FAQ / Knowledge Center) for all product and Customer Care information.Click on the following to link directly to the Residential Product...
E Lock Templates:E51 E193 Metal Template 1 1-8 x 2 1-4 SquareE51 E193 Wood Template 1 1-8 x 2 1-4 SquareEB Lock Templates:EB51 EB52 Metal Template 1 1-8 x 2 1-8 SquareEB51 EB52 Wood Template 1 1-8 ...
ME10N ME40N Metal Template 1 x 2 1-4 SquareME10N ME40N Wood Template 1 x 2 1-4 RadiusME10N ME40N Wood Template 1 x 2 1-4 SquareME10N ME40N Wood Template Drive InME10S MD40S Wood Template 1 x 2 1-4 ...
Schlage does not currently make a non-ic retrofit cylinder for the Sargent 11 Line locks, nor will any of Schlage's conventional cylinders work. 
Sargent 11 Line (T-Zone) locks can be ordered from Sargent, prepped for a Schlage Full Size Interchangeable Core (FSIC) or Small Format Interchangeable Core (SFIC).
Schlage discontinued the MD series handleset lock after the year 2000. Door prep templates for the MD series are below.MD10 MD40 Wood Template 1 x 2 1-4 SquareMD10 MD40 Metal Template 1 x 2 1-4 Squ...
MACS or Maximum Adjacent Cut Specifications for cylinder pinning refers to the maximum variance allowed between one pinned chamber and the adjacent pinned chamber. MACS vary from one manufacturer t...
HOW TO ORDER1. Specify CON for the Allegion Connector electronic options    Example: EL-99-EO-CON, (99 Series Electrified Latching exit only with Allegion Connect)    Example: L...
Can I get Excel spreadsheet data from my Schlage Express Software reports? Yes... in any already generated report from Schlage Express, right click anywhere in the "white space" and Select Expo...
ASA was the acronym for “American Standards Association” and is no longer in existence. The American Standards Association was a standards organization which predated ANSI (American National S...
Cylinder pin information is very unique to the device and application and requires a unique solution. If you have questions related to cylinder pin, please e-mail your request (including a descript...
For Schlage electrified mortise and cylindrical locks, use the following table as a general rule for maximum wire length and wire gauge to be used.This chart shows the wiring sizes and lengths for ...
You can not use an indicator on a mortise holdback function.Indicators change state based on the position of the thumb turn hub in the lockcase. The thumbturn hub will be in one of two different po...
The key retaining cam does not come already installed. At one time the key retaining component could be ordered separately and installed in the field, but they are no longer offered. 
Timing instructions and proper key operation/rotation can be found by clicking here. 
The Schlage LM9200 Series is an innovative one or two point latch solution for pairs of wood doors where both leaves need to be active. Instead of traditional concealed rods, the LM9200 utilizes co...
BE-367  Multi-Family iButton Electronic Deadbolt Features and Specifications                    ...
 All parts (lock, door, rods, frame) must be ordered from Allegion as a package.  Thus you can not “mix and match” with other manufacturers.
Please contact the Allegion Product Support Team on all questions or inquiries pertaining to hardware finishes warranties. Please send an e-mail to the applicable Product Support team:Closers_TechP...
As of June 2015, the new high visibility indicator is available in N escutcheon AND sectional (ROSE) for non cylinder functions such as the L9040, L9044, L9440 and L9444. 
UL listings can be searched at UL.com under Online Certifications Directory.
Please see here for the wire run and wire gauge requirements for the  L9090EL/EU, L9091EL/EU, L9092EL/EU, L9093EL/EU, L9094EL/EU, L9095EL/EU Schlage Mortise locks. 
Apartment Corridor Lock function is defined as a lock where the latch bolt operated by lever from either side, except when outside lever is made inoperative by a stop or mechanical means other than...
The programming processes for Allegion devices can be both product and features specific.  Some products programming processes are electronic in nature, others are physical in nature. &nbs...
The low battery indicator is located on the left-hand side of the touchscreen, below the red and green lock status indicators.
There will be additional prep needed when using the Anti Friction Fire Dead latch on a wood door. Please see here for the Anti-Friction Fire Door Dead Latch template. 
Allegion is excited to announce the introduction of mycredentials.allegion.com MyCredentials allows you to authorize orders for Schlage Primus and Everest restricted key systems through o...
The Schlage Residential B60 deadbolt can be ordered to accept the Schlage 23-030 full size core, product is ordered as B60R6.Additional options:Less Core ( J )Temp Core ( T )Construction Core Progr...
A Knox-Box or Fire Department 911 Box is a small wall-mounted safe that holds building keys for Fire Departments, Emergency Medical Services, and sometimes police to retrieve in emergency situation...
Indicator kits are available as of February 2015 per the attached Marketing Bulletin. A complete list of functions with available indicator kits and part numbers can be found here. &...
Governments around the world are focusing on restricting and eliminating the presence of hazardous materials in products and packaging from the environment to improve the sustainability of our plan...
For information on the American Iron and Steel requirements, please contact material.declaration@allegion.com.
In the 2nd quarter 2015, Pro-Lok discontinued several door prep tools/part numbers and replaced them with new tools/part numbers.  The chart below indicates the discontinued part numbers (see ...
The Allegion Connect wire harnesses use 20 AWG (American Wire Gauge). The molex connector and pins provided with the Allegion Connector Kit (CON-KIT) can accept wires between 20 AWG (maximum) ...
The Allegion Connect Connector Kit does not include a crimping tool.  It can be purchased from companies that carry wiring supplies.  It is Molex part number 63819-0000.The Allegion Conne...
Although Schlage recommends using mild soap and water for cleaning the finishes on locks, a list of common hospital cleaning agents and their possible effects on anti-mocrobial finish can be found&...
Residential style locks are available for applications with doors thinner than 1 3/8", please visit http://www.schlage.com
1-3/8” to 1-3/4” standard. 1-3/4“ to 2 optional. Must be specified
The 442S datasheet can be found here.
The Allegion Connect harness insulation is 3/8" in diameter. The Molex connector at its widest point is 0.633" (just over 5/8"). Harnesses with connectors on both ends would require a minimum openi...
In January 2015, the FSIC cam mounting screw for IC cores changed from a #1 Philips screw to a T10 Torx screw.  This change was made to facilitate cylinder assembly and reduce the likelih...
The C134 keyway can be used in all residential Multi-Family series locks with the following exceptions:F series (to include all residential electronics)J seriesB60 series
Schlage provides a black plastic sectional indicator mounting template (L583-751) with each L-series sectional indicator kit. This template is designed to aid in aligning and drilling pilot holes f...
Schlage does not recommend installing indicators back to back (both sides). Therefore, you cannot order an L9000 series locks with two indicators (both inside and outside).  
The BE467 and FE410 do not log audits while operating in Construction Mode.
The LT10 and LT40 tubular lock cannot be mounted less trim one side.
Although the ADA standards address operable parts of locks – like thumbturns, keypads, turn-buttons, and of course, knobs and levers, keys are not covered by ADA.  ADA requires door and gate h...
The Schlage E/B-series handlesets were discontinued in 1999.
Price Books are not available for public viewing. Please contact your local sales representative or distributor for price request.
This is the Schlage Residential version of the Commercial 606 Satin Brass finish.  The 608 will be a little bit duller than the 606. 
The handing of a lock is important in order to ensure that the correct side of the door is secure, the levers are oriented properly, and that the door closes properly.  There are 2 parts to a ...
Corrosion resistant cylindrical lock is not available.
In June of 2017:14-001 Spring Latch was changed to the 13-24814-019 Dead Latch was changed to the 13-247 
When placing your order (for the locks and mounts) you have to request specifically to have the locks mounted on your PO.  
The Molex connector can be cut off and wired directly.
The set screw part number for the inside SL1/SK1 ligature trim is L583-585.
Lead lining is if offered as a separate component (to be installed in the field).  The parts are offered for various backsets, see pricebook.
For temporary temporary core systems we do stamp A, B or C on the bow of the key to differentiate between the bittings.
Per notes in the PB, the cylinder must be ordered separately.
Schlage acquired Dexter around 2000 (no product was acquired just the name).  Schlage begin selling a new Dexter product line in 2002. 
Depends on the combinating rule and the number of pins (chambers).   For A2  6 pin systems = 4,096 changes For A2 7 pin systems = 16,384 changes   For A4 6 pin systems = 15,625 ...
The Kaba Illco Simplex lock can accept a standard cylinder, FSIC, or SFIC.  You will need to determine what cylinder your particular product accepts.  
In 2014, the Quad Primus keys started shipping with the section stamped on the bow. 
The Steelcraft Paladin Series doors and frames are available in compliance with FEMA 361 and ANSI ICC500-2014.  The door system may include other approved Allegion hardware and components that...
The customer can email cisa.sales@allegion.com or call +39 0546 1880070 (Italy). 
630AM finish is available on both the SL1 and SK1 trim.630AM finish is NOT available with the HSLR trim.  (The extra thickness of the AM coating would cause the trim to bind)
The Schlage Keepsafer DIY home security system discontinued in the late 1980's.
The M504-310 was the old Y shaped spanner wrench which was later replaced by the 021415 spanner wrench.